We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Axcel Picatinny Bow Sight: How to Mount and Set It Up Right

Learn how an axcel picatinny bow sight mounts to a Picatinny rail, how to set the pins and tune it for accuracy. A clear step-by-step guide for new archers.

Updated November 2026

An axcel picatinny bow sight mounts to a bow’s Picatinny rail, a standard accessory rail used across archery and firearms. This guide walks you through checking your rail, mounting the sight, setting the pin height and sighting in at a set distance. Follow these steps and you will have a sight that holds its zero from session to session.

What You Need Before You Start

Before you touch a wrench, confirm that your bow has a Picatinny rail or an adapter that accepts one. Most sights of this type attach with a clamp or dovetail-style foot, so check the sight’s mounting instructions against your bow’s riser. Gather these tools:

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

  • The correct hex or Allen keys listed in the sight’s manual
  • A bow square or level for checking vertical alignment
  • A torque wrench, or the manufacturer’s specified torque values
  • A target at a known distance, such as 20 yards
  • Arrows you have already tuned, with fresh, matched fletching

How to Mount the Axcel Picatinny Bow Sight

Step 1: Position the sight on the rail

Slide the sight onto the rail far enough back that the pins sit at a comfortable distance from your eye. Leave room to adjust forward and back later. Do not tighten anything yet.

Step 2: Level the sight

Use a bow square or level against the sight housing to confirm the pin guard runs vertically. A sight that leans will shoot high or low on one side of the target, and the error grows with distance.

Step 3: Tighten to specification

Tighten the clamp screws evenly, a little at a time, alternating between them. Stop at the torque value in the manual. Over-tightening can deform the mount, while under-tightening lets the sight drift during shooting.

How to Set Pins and Sight In

Start by drawing the bow at your normal anchor point and aiming at the center of the target at 20 yards. Shoot a group of three to five arrows, then adjust the top pin or the sight position until the group centers on your aim point. Once the first pin is set, move back to 30 yards and repeat for the next pin. Mark each pin clearly so you can find the correct pin by sight later.

Shoot from the same anchor and release every time. Changes in your hand position or string contact will move your groups more than most sight adjustments do.

Checklist for Setup Day

  1. Confirm the rail type and the mounting method.
  2. Mount the sight loosely and position it.
  3. Level the sight and tighten to specification.
  4. Sight in the first pin at 20 yards.
  5. Set the remaining pins at your chosen distances.
  6. Recheck the mount screws after your first few sessions.

Common Mistakes

  • Skipping the level check, which causes horizontal drift that looks like an aiming problem.
  • Tightening one screw fully before the others, which can shift the sight out of square.
  • Sighting in with poorly tuned arrows, so the groups reflect the arrows rather than the sight.
  • Changing anchor point or release between sessions and then blaming the sight.
  • Forgetting to recheck screws, which can loosen with repeated shooting.
  • A bow square helps you confirm the sight is vertical before you tighten it. View on Amazon
  • A torque-limited hex key set lets you tighten mount screws to the manufacturer’s values without guessing. View on Amazon

If you are new to sight setup, reading about related steps can help. The guide Garmin Rangefinder Bow Sight: Setup, Calibration and Use Guide covers a different style of sight, while Why Do Archery Attack Bows and Arrows Miss? 6 Causes and Fixes explains how tuning problems can look like sight problems.

FAQ

Do I need a Picatinny rail to use this sight?

Yes, the sight is designed to clamp onto a Picatinny-style rail or a compatible adapter. Check your bow’s mounting options before buying any accessories.

How far back should I sight in the first pin?

Many archers start at 20 yards because it is a common practice distance and makes the first adjustment easier to read. Choose a distance you can shoot consistently.

How often should I check the sight’s mounting screws?

Check them after your first few sessions and then periodically. Retighten to the manufacturer’s specified torque, and consult a professional bowyer if a mount keeps loosening.

Conclusion

A properly mounted axcel picatinny bow sight holds its zero when the mount is level, torqued to specification and sighted in with tuned arrows. Work through the steps in order and keep your anchor and release consistent. With those habits, your pins will mean the same thing every time you draw.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.