We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Arm Guard Override RS3: What It Does and How to Set It Up

Learn what the arm guard override RS3 setting does, when archers should use it, and how to adjust it safely for better form and comfort on the range.

Updated November 2026

An arm guard override on an RS3 setup is a way to change how the forearm guard sits and behaves relative to your bow arm. This guide explains what the override does, how to decide whether you need it, and how to set it up without creating new problems. Most of the work comes down to checking fit, measuring the right points, and testing the change at short range before you shoot at distance.

What the Arm Guard Override Actually Changes

The override adjusts the guard’s position or the way it contacts your forearm, so the bowstring clears your arm cleanly on release. Without it, a poorly placed guard can let the string slap the skin or pull the guard off line. The override is a tuning step, not a fix for poor form, so start by confirming your stance and anchor are consistent.

Shopping for one? See our guide: Maverik Max Arm Guard Review (2026): Features and Performance.

When You Should Use the Override

Consider the override if you notice any of these signs during practice:

  • The string touches your forearm on release, even when your grip is relaxed.
  • The guard shifts toward your wrist or elbow after a few ends.
  • Your arrows group high or low because your bow arm position changes slightly each shot.
  • You have recently changed bows, string length, or draw length.

If none of these apply, leave the factory or standard setting alone. Changing a setup that works adds variables you do not need.

Step-by-Step Setup Process

  1. Shoot a set of six arrows at 10 yards with your current setup and note where the string contacts your arm, if it does.
  2. Loosen the guard mounting hardware just enough to move the guard, without removing it.
  3. Position the guard so it covers the inside of the forearm and sits clear of the string path at full draw.
  4. Tighten the hardware evenly and recheck that the guard does not rotate when you lift the bow.
  5. Draw to anchor, hold for two seconds, and release slowly to check string clearance.
  6. Shoot another six arrows and compare the grouping and contact marks with your first set.

Checking Fit and Clearance at Full Draw

Good clearance should be visible without you having to look for it. At full draw, the string should sit well away from the guard surface, and the guard should not press into your forearm. Recheck after each adjustment, because a small change in guard height can alter string path more than expected. Work in increments of about a quarter inch so you can tell which change made a difference.

Signs the Setting Is Wrong

If you see a fresh mark on your forearm after a session, or if arrows begin to walk after a change, return to the last setting that worked and adjust in smaller steps.

Common Mistakes to Avoid

  • Making several changes at once, which makes it impossible to tell what helped.
  • Tightening the guard so hard that it distorts or cracks the mounting point.
  • Testing only at close range, where string contact often looks fine but fails at longer distances.
  • Ignoring bow arm drift, which can mimic an override problem.
  • Skipping a check after changing string or cable, since those alter the string path.

A simple set of tools makes the adjustment easier and safer.

  • A correct-size hex or Allen key set lets you loosen and tighten mounting hardware without rounding the screws. View on Amazon
  • A bow square helps you confirm that the guard and string are aligned in the same plane. View on Amazon
  • A cloth or padded arm guard liner reduces skin irritation if the string still makes light contact during learning. View on Amazon

FAQ

Is the arm guard override the same as a bow tune?

No. A full bow tune covers nock height, cam timing, and paper tuning, while the override only affects how the guard sits and clears the string. You may need both if you are having accuracy problems.

Can I use the override with a traditional bow?

Setup principles are similar, but traditional bows often rely on a different guard design. Check that your guard type supports the adjustment you plan to make.

How often should I recheck the setting?

Check it at the start of each practice session for the first few weeks, then at least once a month. Recheck after any change to string, draw length, or equipment.

Conclusion

The arm guard override is a useful tuning step when the guard or string path causes contact or inconsistent groups. Make one change at a time, test at both short and longer distances, and return to the last working setting if results worsen. If you have ongoing skin injuries from string contact, consult a qualified archery coach or medical professional before continuing.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Archery Society.