Ripcord Ace Arrow Rest: Setup, Tuning and Tips for Beginners
Learn how to set up and tune a ripcord ace arrow rest, from mounting and cable timing to clearance checks and common fixes for cleaner arrow flight.
Updated November 2026
A ripcord ace arrow rest is a drop-away style rest that holds your arrow up to the moment of release, then gets out of the way so the fletching clears cleanly. This guide walks you through mounting the rest, setting its position, adjusting the cable and tuning for clean arrow flight. You will also learn the mistakes that cause most beginner problems, so you can spend more time shooting and less time fiddling with the bow.
Before you start, keep in mind that every rest works a little differently. Always check the instructions that came with your specific model, because manufacturers specify torque values, cable lengths and clearance numbers that may differ from the general figures below. If anything about your bow’s draw system or cams feels unfamiliar, have a qualified pro shop check the work.
Shopping for one? See our guide: Ripcord Drive Arrow Rest Compared: 6 Best Picks for 2026.
What You Need Before You Start
Gather your tools and parts first. Working on a bow with a clear setup and a stable bench makes the process far easier.
- A rest with its mounting hardware and cable assembly
- Hex keys and a torque driver or torque wrench (manufacturers often specify inch-pound values)
- A bow square and a clean, flat surface
- An arrow matching your draw length, spine and point weight
- Tape measure or calipers
- Paper and pencil for noting your starting measurements
- A bow press, if your cable setup requires one
Step 1: Mount the Rest on the Riser
Start by attaching the rest to the riser at the mounting holes. Most rests use a bracket that slides on a shelf, and the bracket position controls how far the arrow sits from the riser.
Setting the Starting Position
- Set the bracket so the rest sits near the middle of its travel range. This leaves room to adjust in both directions later.
- Tighten the mounting screws loosely at first, so you can still move the rest.
- Check that the rest body sits square to the arrow path and does not tilt up or down.
Torque the Hardware
Once the position looks right, tighten each screw to the torque value in the manual. Over-tightening can strip threads in the riser, while under-tightening lets the rest drift during shooting. Tighten in a cross pattern so the bracket seats evenly.
Step 2: Set the Arrow Center and Height
Arrow centering determines whether the arrow flies straight off the string. Height determines how the arrow sits relative to the sight and the bow’s center line.
Center Shot Basics
Use a bow square to measure from the riser’s center line to the arrow’s center point. Many archers start with a center shot distance in the range the manual suggests for their bow’s cam or grip design. Move the rest in small increments, about 1/32 inch at a time, and shoot a few arrows after each change to see the effect on grouping.
Arrow Height
Set the arrow so its center sits level with or just below the nock point you use for your anchor. A simple test is to shoot paper at close range and watch the arrow’s tail. If the tail dips or the fletching drags on the rest, the height is off.
Step 3: Adjust the Drop-Away Cable
The cable is what makes the rest drop away at release. Setting it correctly is the step most likely to cause problems if rushed.
Cable Length and Timing
- Attach the cable to the rest’s pivot point and to the bow’s cable anchor, following the manual’s routing diagram.
- At full draw, the rest should be fully supporting the arrow. At release, the cable should pull the rest down smoothly and quickly.
- If the rest drops too early, lengthen the cable slightly. If it drops late or not at all, shorten it. Make changes in small steps.
Checking the Drop
Draw the bow slowly to full draw and let down without shooting. Watch the rest. It should stay engaged until you release, then drop without snagging on the arrow or the cable. Repeat this several times to confirm consistency.
Step 4: Tune for Clean Arrow Flight
Once the rest is mounted and the cable is set, tuning is about observing how the arrow leaves the bow.
Paper Tuning Method
Shoot an arrow through a sheet of paper held about three feet from the bow. Look at the tear pattern:
| Tear Pattern | What It Usually Means | Adjustment Direction |
|---|---|---|
| Fletching tear at the top | Arrow is too high on the rest or the rest is too far out | Lower the arrow or move the rest in |
| Fletching tear at the bottom | Arrow is too low or the rest is too far in | Raise the arrow or move the rest out |
| Tear with the arrow tail to the left | Arrow is pushing right of center | Adjust center shot toward the riser |
| Clean hole, no tear | Arrow is flying straight | Fine-tune only if groups are off |
Make one change at a time. Shoot a new paper test after each adjustment so you can connect cause and effect.
Checking Clearance
Look at the fletching as it passes the rest. Each fletching should clear the rest body without brushing it. If you hear a ticking sound or see scuff marks on the rest, the clearance is too tight.
Common Mistakes
- Skipping the torque check. Loose hardware causes the rest to shift and makes tuning impossible to repeat.
- Making large adjustments. Move in small steps and retest. Big changes hide the true problem.
- Ignoring the cable. A cable that drops late can throw arrows off target even with perfect centering.
- Tuning with a damaged arrow. Bent shafts or worn nocks will confuse your paper results.
- Forgetting to recheck after bow adjustments. Changing draw weight or cams can shift the arrow path, so retune after major changes.
Tips for Better Results
- Keep a written log of every adjustment and the result, including the date and arrow setup.
- Shoot a consistent release. Rest drop problems often look like tuning problems.
- Check the rest’s pivot and cable after every few hundred arrows, since parts wear over time.
- Use a bow press when servicing the cable, and never work on a string or cable under tension without one.
- If your arrows keep tearing paper in the same direction after you have adjusted the rest, check the nock fit and fletching alignment before changing the rest again.
Recommended Gear
These items can make setup and maintenance easier for a ripcord ace arrow rest. Confirm compatibility with your bow and rest model before buying.
- Bow square. A reliable square gives you a consistent reference for measuring center shot and arrow height. View on Amazon
- Torque driver. Setting hardware to the manufacturer’s specified value prevents stripped threads and rest drift. View on Amazon
- Paper tuning kit. A paper holder with tuning paper lets you check arrow flight quickly at close range. View on Amazon
- Bow press. Needed for safe cable and string work on most compound bows. View on Amazon
FAQ
Is a ripcord ace arrow rest suitable for beginners?
Yes, with careful setup. The drop-away action is simple to use once the cable and position are right, but it does reward patient tuning. Owners often report that a shop setup for the first mount saves time.
How often should I check the rest?
Check the hardware and cable before each shooting session if you are still learning. After that, a weekly visual inspection and a full check every few hundred arrows is a reasonable routine.
Why does my arrow still tear paper after tuning?
The cause is often arrow spine, nock fit or fletching alignment rather than the rest. Confirm your arrows match your draw weight and length, then retest.
Can I adjust the rest without a bow press?
Position adjustments on the bracket usually do not require a press. Cable work does, and you should use one for any change that involves tension.
What is the most common cause of inconsistent groups?
Inconsistent release and loose hardware cause most inconsistent groups. Fix your shooting form and recheck torque before blaming the rest.
Should I replace a worn cable?
Yes, if you see fraying, stretching or a cable that no longer drops reliably. Follow the manufacturer’s replacement guidance and have a shop help if you are unsure.
Does draw weight change affect the rest setup?
It can. Changes to draw weight or cam timing may shift the arrow path, so retune center shot and paper results after any major change.
Conclusion
A ripcord ace arrow rest rewards careful mounting, measured cable setup and small, logged tuning steps. Work through the hardware, centering and cable checks in order, and use paper tests to confirm each change. Consult a professional bow technician if you are unsure about any step, especially cable work.
Related reading
- Ripcord Ratchet Arrow Rest: How It Works, Setup Steps and Tips
- Ripcord Rak Arrow Rest: Setup, Tuning and Tips for Beginners
- Ripcord Arrow Rest Replacement Parts: What to Buy and How to Swap Them
Ready to choose one?
