Drop Away Arrow Rest Mathews: Setup, Tuning and Buying Guide
Learn how to choose, install and tune a drop away arrow rest for Mathews compound bows, with setup steps, common mistakes and buying tips.
Updated November 2026
A drop away arrow rest for Mathews bows holds your arrow firmly during the draw, then drops out of the way the moment you release. This guide walks you through choosing a drop away arrow rest Mathews owners can rely on, installing it, setting it up for clean arrow flight, and avoiding the mistakes that cost new archers accuracy.
What a Drop Away Arrow Rest Does on a Mathews Bow
A drop away rest is a launcher-style arrow support that sits below the arrow shelf and pivots out of the arrow’s path after the shot. Most designs use a cable or cam-driven mechanism tied to the bow’s draw cycle. When you come to full draw, the rest is held up under the arrow. When the string leaves the fingers, the rest drops away, so the fletching and shaft have a clear path. Owners often describe this as the main reason they chose a drop away over a fixed rest: the arrow is supported right up to release, and nothing is left in the way afterward.
Shopping for one? See our guide: Drop Away Arrow Rest: 5 Best Picks Compared for Compound Bows (2026).
Mathews bows are built around a cam and cable system that already controls draw length and let-off, so the rest needs to work in harmony with that timing. For that reason, it matters that you match the rest to the bow’s cable setup and riser, and that you follow the manufacturer’s install specs. If you are new to rest types, the article What Holds Arrows in Archery: Quivers, Arrow Rests and Holders Explained covers how these parts differ.
Choosing the Right Drop Away Rest for a Mathews
Before you buy, confirm three things: the riser mounting pattern, the cable configuration on your bow, and whether you shoot right-handed or left-handed. Most drop away rests mount to the riser with a standard pattern, but the bracket and cable guard vary, and some models are sold in left-hand versions only.
Key Factors to Compare
| Factor | What to Look For | Why It Matters |
|---|---|---|
| Mounting style | Bracket that matches your riser and cable guard | Wrong mounting causes poor timing and rattle |
| Handedness | Right or left version | The rest must sit on the correct side of the arrow |
| Drop action | Smooth, consistent drop with no bounce | Bounce can disturb arrow flight |
| Adjustability | Vertical, lateral and tension adjustments | Lets you fine-tune for different arrows |
| Noise level | Dampening material and quiet trigger | Noise can spook game in hunting setups |
| Arrow size range | Support for your shaft diameter | Poor contact affects consistency |
If you hunt, noise and drop speed deserve extra weight in your decision. If you shoot targets, adjustability and repeatability are the priorities. For a broader comparison of options, see Drop Away Arrow Rest for Compound Bow: 7 Best Picks Compared (2026) and Quietest Drop Away Arrow Rest: 7 Best Picks Compared (2026). If you’re torn between drop away and simpler styles, Drop Away Arrow Rest vs Whisker Biscuit: Which Should You Choose? lays out the trade-offs.
Tools and Parts You Need Before Installation
Gather everything first so you are not stopping mid-install with the bow half-assembled.
- Hex keys and Allen wrenches sized to the rest’s hardware (check the manual)
- A bow square or drop-away-specific square for checking vertical alignment
- A cable guard or cable slide, if the rest requires one for your setup
- Nock locator or a fresh string with a correct nock point
- Bow stand or holder that keeps the bow steady
- A pen or marker for noting original settings
- Your arrows, cut to the correct length and matched for weight
Step-by-Step Installation on a Mathews Riser
Step 1: Remove the Existing Accessory and Clean the Mount
Take off any existing rest, sight bracket or stabilizer clutter from the riser window. Wipe the mounting surface clean. Grit or old adhesive can shift the rest after a few sessions, which looks like a tuning problem but is really a fit problem.
Step 2: Attach the Bracket Loosely
Thread the mounting bolts in finger-tight. Do not fully tighten yet. Leaving them loose lets you slide the rest into the right position before you lock it down.
Step 3: Set Initial Height and Center
Set the rest so the arrow shaft sits level with the shelf and centered on the bow’s center shot line. Many archers start with a centered rest and then fine-tune. A rough starting point is to match the arrow’s center to the riser’s center line, then check with a square.
Step 4: Connect the Cable and Set the Drop Timing
Attach the drop cable to the cam or cable system as the manufacturer specifies. Set the timing so the rest stays up under full draw and drops at the release point. Test this with the bow unstrung-free and slowly drawn, watching the mechanism rather than relying on the feel of a full shot.
Step 5: Tighten Everything and Recheck
Once the position looks right, tighten bolts to the torque or snugness the manual lists. Recheck height, center and cable tension. Vibration during the first shots can loosen fasteners, so plan on checking again after your first session.
Tuning for Clean Arrow Flight
Installation gets the rest on the bow. Tuning gets the arrow flying straight through it. Work through these checks with a bare shaft and then a fletched arrow.
Paper Tuning Check
Shoot a bare shaft through paper about 3 to 4 feet from the target. A bare shaft that tears a clean hole with the fletching-side tear pointing consistently is a good sign. If the tear is off to one side, adjust the rest’s lateral position in small increments and retest.
Walk-Back Tuning
From about 10 to 20 yards, shoot a group with fletched arrows. Walk back in steps, looking at the group pattern. Arrows that fly left or right usually point to lateral rest position; high and low groups often point to nock point or vertical rest height.
Checklist for Consistent Results
- Confirm arrow length and weight match your draw and target goal
- Check nock point with a nock locator
- Verify the rest is square to the bow and centered
- Test the drop action slowly, then at normal speed
- Paper tune and walk-back tune before any serious shooting
- Recheck fasteners after the first several sessions
Common Mistakes to Avoid
- Using the wrong handedness. A left-hand rest on a right-handed setup will never shoot right.
- Skipping the cable timing check. A rest that drops early or late can cause erratic groups.
- Over-tightening mounting bolts. This can crack or distort the bracket. Snug is usually enough.
- Tuning with a dirty or worn rest. Clean the arrow contact point and replace worn parts.
- Chasing tuning with the wrong arrows. If spine or weight is wrong, no rest adjustment will fix the group.
- Ignoring noise. A loose bracket or dry cable can rattle, which matters most in hunting.
Recommended gear
- Drop away arrow rest made for Mathews bows: Choose a model listed for your riser and cable setup, since fit drives both accuracy and quietness. View on Amazon
- Nock locator: A nock locator helps you set nock point consistently, which is essential for rest tuning. View on Amazon
- Bow square: A square lets you check rest alignment against the bow’s centerline before you shoot. View on Amazon
- Bow stand: A stable stand keeps the bow still while you adjust cables and mounting hardware. View on Amazon
FAQ
Is a drop away arrow rest better than a fixed rest?
It depends on your goals. A drop away supports the arrow until release and clears the fletching afterward, which many archers prefer for accuracy and hunting. A fixed rest is simpler and has fewer moving parts to maintain.
Can I install a drop away arrow rest on any Mathews bow?
Not always. Check the manufacturer’s compatibility list for your specific riser model, cable configuration and year. Mounting patterns and cable guards differ across Mathews lines.
How do I know if my drop away is timed correctly?
The rest should hold the arrow under full draw and drop cleanly at release, without hanging up or bouncing. Test slowly with the bow in a stand, then confirm with paper tuning and walk-back groups.
Why does my arrow hit left or right of the target center?
Lateral rest position, nock point and arrow spine are the usual causes. Start with paper tuning to see the arrow’s flight direction, then adjust the rest in small steps.
How often should I check the rest hardware?
Check mounting bolts and cable connections after your first few sessions and periodically after that. Vibration loosens fasteners over time.
Do I need a left-handed drop away for a left-handed shooter?
Yes. Left-handed shooters need a left-hand configured rest so the arrow sits on the correct side of the bow.
When should I consult a professional?
If you are unsure about cable timing, riser damage, or drawing a bow with a bent limb or worn cable, have a qualified archery pro or bow shop inspect it. Working on a loaded bow carries real risk of injury.
Conclusion
A drop away arrow rest can give a Mathews bow a clean, quiet release when it is matched to your riser, timed correctly and tuned with patience. Work through installation in order, use paper and walk-back tuning to confirm results, and recheck hardware regularly. With a dialed-in setup, you can focus on form instead of troubleshooting the rest.
Related reading
- Quietest Drop Away Arrow Rest: 7 Best Picks Compared (2026)
- Drop Away Arrow Rest vs Whisker Biscuit: Which Should You Choose?
- Drop Away Arrow Rest for Compound Bow: 7 Best Picks Compared (2026)
- Drop Away Arrow Rest Cable Clamp: 5 Best Picks Compared (2026)
- 7 Best HDX Drop Away Arrow Rests for Compound Bows (2026)
Ready to choose one?
