We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Custom Made Archery Arm Guard: A Step-by-Step Guide for Target Archers

Learn how to get a custom made archery arm guard that fits your forearm, bow arm and shooting form. Covers measuring, materials, fitting and common mistakes.

Updated November 2026

A custom made archery arm guard is built around your own forearm measurements, your bow arm position and the way you shoot, so it protects you from string slap without shifting, bunching or rubbing. In this guide you will learn how to measure correctly, choose materials, decide between a made-to-order piece and a DIY build, check the fit and keep the guard in good shape. The goal is a guard you forget about once you start shooting.

Why Custom Fit Matters for Arm Guards

A standard arm guard is sized to a range of forearms, which works for many archers but rarely fits perfectly. If the guard is too short, the string can still catch the skin above or below it. If it is too loose, it slides toward the wrist during the draw and leaves a gap. A custom guard solves both problems by matching the exact length, width and curve of your forearm. Many archers also find that a custom piece lets them place the strap and lacing where they want rather than where the manufacturer decided.

Shopping for one? See our guide: 3 Best Custom Leather Archery Arm Guards for Target Archers (2026).

Step 1: Decide What You Need From the Guard

Before you measure anything, define the job. Most target archers want protection from string slap on the inside of the forearm and the outside edge where the string travels after release. Some want full coverage from wrist to just below the elbow, which is common with longer bows or wider string paths. Others prefer a shorter guard that protects the most-hit area and leaves the rest of the arm free for a clean follow-through.

Think about your bow style too. A recurve bow often needs a guard with a slightly different contour than a compound, and a traditional bow may call for a longer strap. If you are unsure, read about how a recurve bow arm guard differs from other designs. The more clearly you define the purpose, the better your custom piece will perform.

Step 2: Measure Your Forearm Correctly

Accurate measurements are the foundation of a good custom guard. Use a flexible tape measure, and take readings with your bow arm held in your normal shooting stance: elbow slightly bent, forearm relaxed, wrist neutral.

  1. Wrist circumference: Measure just above the wrist bone where the guard will sit.
  2. Forearm width at the target point: Measure across the forearm at the spot where the string usually strikes, typically a few inches below the elbow on the inside.
  3. Total length: Measure from the base of the wrist to the point where you want the top edge to end. For a standard guard this is often a few inches below the elbow crease; for a longer coverage guard, go farther up the forearm.
  4. Forearm circumference at the top edge: Measure at the upper boundary so the guard wraps without pinching.
  5. Clothing allowance: If you shoot with a jacket or a thick sleeve, add a small amount to the circumference measurements so the guard can be worn over it.

Write every number down and label it. Measure both arms if you are unsure which will be the bow arm, since many archers have a slightly different size on each side.

Step 3: Choose the Right Material

Material affects comfort, noise, durability and how the string behaves on contact. Leather is the most common choice for custom guards because it molds to the arm over time and is quiet on release. Synthetic materials such as neoprene or padded composites are lighter and resist moisture better, while some archers choose a hybrid with a leather face and a soft backing.

Material Strengths Trade-offs
Full-grain leather Molds to the arm, quiet, long-lasting Needs occasional conditioning, slower to dry
Suede or split leather Soft feel, comfortable against skin Less durable where the string hits
Neoprene or synthetic Lightweight, handles moisture well Can feel warm, may be louder on contact
Leather with synthetic backing Balance of durability and comfort Heavier, more complex to make

Thickness also matters. Thin material is quieter but offers less protection, while very thick leather can restrict movement. Many archers settle on a moderate thickness that they can bend easily but that still stops the string cleanly.

Step 4: Decide Between Made-to-Order and DIY

You have two main routes. A made-to-order guard is produced by a maker who works from your measurements and any specifications you send, and it is the simplest option if you want professional finishing. Some sellers also offer adjustable designs that let you fine-tune the fit later. For a broader look at what is available, see this custom leather arm guard buyer’s guide.

A DIY guard lets you control every detail, from the cut shape to the placement of the strap. It takes patience and basic leatherworking tools, and the first attempt often needs adjustment. If you go this route, a printed or drafted leather arm guard template gives you a reliable starting shape.

Step 5: Plan the Shape and Strap System

Once you know your measurements and material, sketch the guard shape. A slight curve that follows the natural contour of the forearm usually sits better than a flat rectangle. Most guards use one of these closures:

  • Lacing: Adjustable and secure, but takes time to tie and can loosen with use.
  • Hook-and-loop strap: Quick to put on and easy to tighten by feel.
  • Buckle or snap strap: Firm and repeatable, good for archers who want the same fit every session.

Place the strap so it sits on the back of the forearm, away from the string path, and make sure no buckle or stitching lies where the string or your sleeve will catch.

Step 6: Test the Fit Before Shooting

Put the guard on, set your stance and draw an unloaded bow or a bow at low draw weight. Check these points:

  • The guard stays in place when you lift the bow and relax the arm.
  • It covers the spot where the string normally lands during release.
  • Your wrist can flex naturally, and the strap does not dig in.
  • The string does not pinch the edge of the guard during the draw.
  • Your sleeve, if worn, does not bunch under the guard.

Shoot a few arrows at a short distance and watch for string contact. A clean, quiet release with no pinching or sliding means the fit is right. If the guard moves, tighten the strap or adjust the length before making any structural changes.

Step 7: Care for and Maintain Your Guard

Leather guards last years with basic care. Wipe off sweat and dirt after each session, let the guard air dry away from heat, and apply a leather conditioner a few times a year to keep it supple. Check the stitching and strap hardware regularly, since loose threads or worn hook-and-loop can cause the guard to fail mid-shoot. Store it flat or hung rather than folded tightly, which can create creases that weaken the leather.

Tools and Materials Checklist

If you plan to make or modify a guard yourself, gather these items:

  • Flexible tape measure and pencil
  • Cardboard or paper for a pattern
  • Leather of the chosen thickness
  • Sharp utility knife or leather shears
  • Leather punch or awl
  • Waxed thread or leather lacing
  • Hook-and-loop strap or buckle hardware
  • Leather conditioner

Common Mistakes to Avoid

  • Measuring with a relaxed or bent arm: Always measure in your shooting position so the guard fits when you draw.
  • Making the guard too tight: A tight guard restricts blood flow and shifts during the shot. It should feel snug, not constricting.
  • Ignoring the strap position: A strap that sits in the string path can catch or cause noise.
  • Choosing material only for looks: Pick material for quiet release and durability first.
  • Skipping the test shoot: A guard can look right on the table and still move once you start drawing.

Tips for Better Results

  • Make a paper pattern first and test it on your arm before cutting leather.
  • If you are between sizes, choose the slightly larger measurement and adjust the strap.
  • Break in new leather by wearing it around the house for a few hours before shooting.
  • Keep a spare strap or lace on hand so a single failure does not end your session.

Good tools make a custom guard easier to build and maintain. A leather conditioner keeps the material flexible between seasons, which helps the guard stay quiet. A sharp leather knife produces clean edges that resist fraying. A set of leather punches creates consistent lacing holes so the closure lines up every time. Owners often report that a leather-specific conditioner works better than general-purpose oils, which can darken or soften the surface too much.

FAQ

How do I know if I need a custom arm guard instead of a standard one?

Consider a custom guard if standard sizes leave gaps, shift during the draw, or fail to cover the string path on your arm. Archers with unusual forearm proportions often benefit most.

How long does a custom leather guard last?

With regular cleaning and occasional conditioning, a well-made leather guard can last several years. Replace it when the string-contact area thins, the stitching loosens or the strap no longer holds.

Should the guard be worn over or under a sleeve?

Most archers wear the guard over a thin sleeve or shirt so the sleeve reduces friction. Confirm the sleeve does not bunch under the guard during the draw.

What thickness of leather is best for an arm guard?

A moderate thickness that bends easily while still stopping the string is typical. Very thick leather can restrict wrist movement, and very thin leather may not protect well.

Can I adjust a custom guard after I receive it?

Guards with hook-and-loop or buckle closures can usually be tightened or loosened. Length changes are harder and may require a new strap or a maker’s adjustment.

How do I clean a leather arm guard?

Wipe it with a slightly damp cloth after shooting, let it air dry away from direct heat, and condition it a few times a year. Avoid soaking the leather.

Is a custom guard worth it for a beginner?

Beginners often start with a standard guard to learn their form, then order a custom piece once their draw and bow arm position settle. If you have an unusual fit or frequent string slap, a custom guard can help sooner.

Should I consult a professional about fit?

If you experience persistent bruising, numbness or pain in the forearm or wrist, stop shooting and consult a doctor or physical therapist. A certified archery instructor can also check your form and guard placement.

Conclusion

A custom made archery arm guard starts with careful measurement, clear goals and the right material. Whether you order from a maker or build your own, test the fit with real draws before trusting it on the range. With regular care, a well-fitted guard keeps your bow arm protected and your release quiet for years. Revisit the fit whenever your form or clothing changes, and adjust as needed.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Archery Society.