Barnett Tomcat Arrow Rest: Setup, Tuning and Buying Tips
Learn how the barnett tomcat arrow rest works, how to set it up and tune it for clean arrow flight, and what to check before you buy.
Updated November 2026
The barnett tomcat arrow rest is a drop-away style rest that many archers consider when they want a simple, adjustable shelf for holding an arrow before the shot. This guide explains what the rest does, how to install it, how to tune it so your arrows fly cleanly, and what to look for when you compare options. By the end, you should be able to mount the rest on a compound bow, set its position and tension, and spot the common problems that cause inconsistent arrow flight.
What the Barnett Tomcat Arrow Rest Does
An arrow rest supports the arrow on the bow’s riser while you draw, then gets out of the way as the arrow leaves the string. A drop-away rest, the category this model belongs to, lowers or pivots its arrow support after the shot so the fletching does not brush against it. For a broader look at how rests differ from quivers and holders, see What Holds Arrows in Archery: Quivers, Arrow Rests and Holders Explained.
Shopping for one? See our guide: Arrow Rest for Compound Bow: 6 Best Picks Compared (2026).
Rests are only part of the equation. Your bow’s draw weight, arrow spine, point weight and shooting form all affect how the arrow leaves the bow. A rest that is mounted and adjusted carefully gives you a consistent launch point, which makes tuning easier and groups tighter.
Before You Start: Tools and Preparation
Gather the following before you begin installation:
- A hex (Allen) key set matching the rest’s mounting screws
- A bow square or a square-edged tool for checking alignment
- A bow press or a stable bow stand
- A tape measure or ruler with 1/32-inch markings
- A roll of painter’s tape or a piece of paper for a paper tune
- Thread-locking compound (a low-strength formula) for screws
- A clean rag and a bow-safe degreaser
Read the manufacturer’s installation sheet for the specific model you own. Torque specifications, mounting hole locations and included adapters can vary between production runs, so trust the instructions over general advice when they conflict.
How to Install the Barnett Tomcat Arrow Rest
Step 1: Choose the Mounting Position
Most drop-away rests mount to the riser through a series of threaded holes. Start by placing the rest where the arrow will sit just above the arrow plate on a centered, level shelf. Check that the arrow will clear the riser and the cable guard when the bow is drawn.
Step 2: Attach the Base Without Fully Tightening
Thread the mounting screws in finger-tight. Leave them loose enough that you can slide the rest a few millimeters. This lets you fine-tune the position during the paper tune instead of fighting a rest that is locked in the wrong place.
Step 3: Set the Rest Height and Arm Position
Adjust the arrow support so the arrow sits level when nocked. Most archers find that a level arrow, measured from the shelf to the nock point, gives a neutral starting point. Set the arm so the arrow rests on the shelf without binding.
Step 4: Set Launcher or Tension Controls
Many drop-away rests include a tension or launch control. Start with the manufacturer’s recommended setting, then adjust in small increments during tuning. Too much tension can throw the arrow to one side. Too little can let the arrow sag or fall off the shelf.
Step 5: Tighten and Check Alignment
Once the position feels right, tighten the mounting screws evenly, a little at a time, to avoid bending the bracket. Check that the rest sits square to the bow’s center line. Apply thread-locking compound only to the screws you will not need to remove often.
How to Tune the Barnett Tomcat Arrow Rest
Tuning is where most of the accuracy comes from. The paper tune is the most common starting method for compound bows and works well with this rest type.
Paper Tune Steps
- Stretch a sheet of paper across a frame about 3 feet from the bow.
- Shoot an arrow through the paper at close range while holding the bow steady.
- Look at the tear. A clean hole with feathers or fletching marks in the center suggests good alignment.
- If the tear shows the arrow entering left of center and tearing right, the arrow is tail-left. Adjust the rest to move the shelf or the arrow path.
- Make one small adjustment at a time, shoot again, and repeat until the tear is consistent.
Checking Arrow Flight at Distance
After paper tuning, shoot a group at 20 yards. A tight group that drifts in one direction usually points to rest height or tension. A wide scatter may suggest a form issue or arrow spine that does not match your draw weight. Adjust one variable at a time and record what you change.
| Symptom | Likely Cause | What to Adjust |
|---|---|---|
| Arrow tears left on paper | Rest position too far left | Move rest slightly right |
| Arrow tears up | Rest too low or too high | Adjust height in small steps |
| Arrow hits high at distance | Tension or launch too strong | Reduce tension slightly |
| Arrow falls off shelf | Shelf angle or tension too low | Check shelf level, increase tension a little |
Buying Tips for the Barnett Tomcat Arrow Rest
When you compare drop-away rests, check the following features before you decide:
- Mounting compatibility: Confirm the hole pattern matches your riser.
- Adjustability: Look for independent height, tension and left-right controls.
- Arrow diameter: Make sure the shelf and arm suit your arrow shaft size.
- Drop-away action: A reliable, quiet drop after the shot reduces fletching contact.
- Replacement parts: Check whether felt, springs and screws are easy to find.
For a wider comparison of rests in this category, see Barnett CenterShot Arrow Rest: Setup, Tuning and Buying Tips and Quality Archery Arrow Rests: 7 Best Picks Compared (2026). If you prefer a different style, Trophy Taker Arrow Rest: Setup, Tuning and Buying Tips for Beginners covers another common option.
Common Mistakes
- Over-tightening mounting screws. This can strip threads or warp the bracket. Tighten evenly and stop when the rest no longer shifts.
- Tuning too many variables at once. Change one setting, then shoot and observe.
- Ignoring arrow spine. A rest cannot fix an arrow that is too stiff or too weak for your draw weight.
- Skipping a regular check. Rest screws can loosen with vibration. Inspect them before each practice session.
- Forgetting the cable guard. Verify clearance between the rest, the arrow and the cable guard at full draw.
Tips for Better Results
- Keep a tuning log with rest settings, arrow weight and group results.
- Retune after changing arrows, string or draw length.
- Check the drop-away action at full draw and after a few shots.
- Clean the shelf and felt surfaces periodically so the arrow slides cleanly.
Recommended gear
A few items can make installation and tuning easier:
- Bow press: A stable press holds the bow still during mounting and adjustment. View on Amazon
- Bow square: Checks that the rest sits square to the riser. View on Amazon
- Paper tuning frame: A simple frame keeps your paper steady for consistent tears. View on Amazon
- Hex key set: A full set covers the small screws found on most rests. View on Amazon
FAQ
Is the barnett tomcat arrow rest suitable for beginners?
Yes, with patience. Its adjustments are straightforward, but tuning still takes time. Follow the paper tune steps and change one setting at a time.
How often should I check the rest?
Check the screws and drop-away action before each session, and retune after any change to your arrows, string or bow setup.
Can I use a paper tune with this rest?
Yes. The paper tune is a common first step for a drop-away rest like this one. Confirm the result with a group at 20 yards.
What arrow spine should I use?
Spine depends on your draw weight, draw length, point weight and arrow length. Use a spine chart from your arrow manufacturer as a starting point, then confirm with tuning.
Why does my arrow fall off the shelf?
This is usually caused by low tension, a shelf that is not level or an arrow that is not nocked squarely. Check each item and adjust gradually.
Should I apply thread-locking compound to the screws?
A low-strength thread-locking compound can help prevent loosening. Use it sparingly and only on screws you do not expect to remove often.
When should I ask a professional for help?
If the rest will not hold its position, if you see cracks or stripped threads, or if you are unsure about torque or mounting, consult a qualified pro shop technician.
Conclusion
The barnett tomcat arrow rest can give you a reliable, adjustable shelf when it is mounted carefully and tuned in small steps. Start with a sound installation, use a paper tune to find your baseline, then confirm with a group at distance. Keep a log of your changes so you can repeat good results and troubleshoot problems quickly.
Related reading
- Whisker Biscuit Arrow Rest Installation: A Step-by-Step Guide
- Trophy Ridge Sync Arrow Rest: 5 Best Picks Compared (2026)
Ready to choose one?
