Arrow Rest Felt Replacement: Step-by-Step Guide for Clean Arrow Flight
Learn how to replace arrow rest felt step by step, from choosing material and removing old felt to setting height and checking arrow flight.
Updated November 2026
An arrow rest felt replacement is a simple repair that can restore clean arrow flight and quiet shots on a shelf or flipper-style rest. In this guide you will learn how to identify worn felt, choose a suitable replacement material, remove the old pad, install and trim the new one, and check that your arrows still clear the riser properly. The whole job usually takes under an hour with basic tools.
When Arrow Rest Felt Needs Replacing
Felt does a lot of quiet work. It cushions the arrow shaft, reduces noise on the shot, and helps the arrow leave the rest smoothly. Over time, it compresses, tears, picks up fletching debris, or absorbs bow lubricant. Replacing it before problems show up in your groups is easier than chasing a tuning issue later.
Shopping for one? See our guide: Arrow Rest for Compound Bow: 6 Best Picks Compared (2026).
Watch for these signs:
- Flattened or compressed felt where the shaft rests, usually a visible groove.
- Torn or frayed edges that catch fletching.
- Arrows that hit the rest with a louder slap than normal.
- Shafts showing scuff marks or fresh wear on one side.
- Felt that has become stiff, glossy, or discolored from oil or wax.
If your rest uses a different cushioning system, such as a plastic or rubber cushion, check your manufacturer’s instructions before swapping materials. Some rests are not designed to accept felt at all.
Choosing the Right Replacement Felt
Most rests with a felt pad accept a self-adhesive or peel-and-stick felt strip sized to the cradle. Some archers cut their own pads from a sheet of quality felt and secure them with adhesive. Either approach works, but the goal is the same: a pad that is firm enough to hold the arrow steady and soft enough to avoid marking the shaft.
| Felt Type | Typical Use | Notes |
|---|---|---|
| Pre-cut adhesive strip | Most shelf and flipper rests | Fastest option; match the size to your rest’s cradle |
| Sheet felt, 1/16 inch | Custom cuts for unusual rests | Cut to the cradle shape and glue in place |
| Thicker sheet felt, 1/8 inch | Heavier draw or older equipment | Can increase cushion; check clearance on the arrow |
Before buying, measure the cradle width and length. Note whether your old felt was flat or contoured. Write down the thickness too, since a thicker pad raises the arrow slightly and can change centershot or nock height.
Checklist: What You Need
- Replacement felt, sized to your rest
- A sharp hobby knife or utility blade
- Fine-grit sandpaper or a scraper
- Isopropyl alcohol and a clean cloth
- A small flat-blade screwdriver or plastic pry tool
- Painter’s tape or masking tape
- A metric and imperial ruler or caliper
- Contact cement or adhesive, if your felt is not self-adhesive
Step-by-Step: Removing the Old Felt
Step 1: Secure the Bow
Set the bow in a bow stand or lean it against a stable surface with the rest facing up. Remove the arrow and any quiver that could get in the way. Working on a stable bow reduces the chance of bending a limb or scratching the riser.
Step 2: Peel Off the Old Pad
Slide a plastic pry tool or the edge of a flat screwdriver under one corner of the felt. Lift slowly and pull the pad away in one piece if possible. If it resists, warm it gently with a hair dryer on low for 15 to 20 seconds to soften the adhesive.
Step 3: Clean the Cradle
Remove leftover adhesive with a fingernail, a plastic scraper, or fine sandpaper used lightly. Wipe the surface with isopropyl alcohol and let it dry completely. A clean, dry surface is essential. Oil, wax, or dust will prevent the new felt from bonding well.
Installing the New Felt
Step 4: Dry-Fit the Pad
Place the new felt against the cradle without removing the backing. Check that it sits flush with the arrow path and does not overhang the edges. If you are cutting custom pieces, trace the cradle onto the felt and cut slightly inside the line, then test again.
Step 5: Apply the Felt
For self-adhesive felt, peel the backing and press the pad into place starting from the center and working outward. Use firm, even pressure. For glued felt, apply a thin, even coat of contact cement to both surfaces, wait until it is tacky according to the adhesive instructions, then press them together and hold for a moment.
Step 6: Trim and Smooth
Use a sharp blade to trim any excess felt along the edges. Cut with light, steady strokes to avoid tearing. Smooth the surface by hand so there are no lifted corners or bubbles that could catch fletching.
Step 7: Allow Curing Time
Give the adhesive time to set before shooting. Most contact cements need several hours. Self-adhesive felt often feels secure right away, but waiting an hour or two reduces the chance of the pad shifting during your first session. Follow the product label for exact times.
Checking Arrow Clearance and Flight
A new pad can change how the arrow sits, so check the setup before shooting groups.
- Nock an arrow and check that the shaft rests evenly on the felt without tilting.
- Confirm that the fletching clears the riser and the rest arm at full draw.
- Shoot two or three arrows at a close target, around 10 yards, and look for paper tears or contact marks on the shaft.
- Listen for noise. A quiet release usually means the pad is seated correctly.
- If the arrows now fly differently, check your nock height and rest height before adjusting anything else.
If you notice persistent tears on the fletching or a consistent shift in group placement, the rest may need a closer look. For a broader view of how the rest fits into your setup, see What Holds Arrows in Archery: Quivers, Arrow Rests and Holders Explained.
Common Mistakes
- Skipping the cleaning step, which causes new felt to peel within days.
- Choosing a pad that is too thick, raising the arrow and changing nock height.
- Cutting felt before dry-fitting, leaving gaps or overhangs.
- Using household glue that softens or stains the felt.
- Shooting immediately after installation before the adhesive has set.
- Ignoring clearance checks and assuming the new pad fits without testing.
Tips for Longer Felt Life
- Wipe the felt with a dry cloth after shooting to remove dust and grit.
- Keep bow lubricant and string wax away from the rest area.
- Inspect the pad before each session, especially after a long day outdoors.
- Keep a spare pad in your kit so a worn one never ends a practice session early.
- If your rest uses a whisker or brush system instead, the replacement process differs. See Whisker Biscuit Arrow Rest Installation: A Step-by-Step Guide for those setups.
Recommended gear
Several items make the job easier and the results more consistent.
- Self-adhesive arrow rest felt pads: Pre-cut strips sized for common rest cradles reduce measuring and trimming, which helps beginners. View on Amazon
- Hobby knife with replacement blades: A sharp blade gives clean edges on custom cuts and prevents felt from tearing. View on Amazon
- Contact cement for felt: Useful if you are gluing sheet felt instead of using adhesive-backed strips. View on Amazon
- Digital caliper: Helps you measure cradle dimensions and felt thickness accurately before buying. View on Amazon
FAQ
How often should arrow rest felt be replaced?
There is no fixed schedule. Replace it when you see compression, tears, or changes in arrow noise. Archers who shoot daily may need new felt more often than those who shoot a few times a month.
Can I reuse felt after removing it?
Usually no. Once felt is peeled, the adhesive is weakened and the pad is often compressed or torn. A fresh pad gives more reliable contact and cushioning.
Does thicker felt change arrow flight?
It can. A thicker pad raises the shaft, which can alter nock height relative to the rest and affect how the arrow leaves the bow. Check clearance and tune if needed.
What is the best glue for arrow rest felt?
Many archers use contact cement designed for fabric or leather. Avoid general household glues that may soften or stain the felt. Follow the adhesive label for application and curing times.
Why does my new felt keep peeling?
The surface was probably not cleaned fully. Oil, wax, or dust prevents bonding. Clean with isopropyl alcohol, let it dry, and reapply. Warmer room temperatures also help adhesive set.
Will replacing felt fix my grouping problems?
Not always. Felt affects arrow contact and noise, but grouping issues often come from nock height, rest position, or paper tuning. Replace the felt first, then check the rest of your setup systematically.
Should I consult a professional?
If your rest is damaged, loose, or part of a warranty, contact the manufacturer or a qualified pro shop before making repairs. A technician can confirm whether felt replacement is appropriate for your model.
Conclusion
Replacing arrow rest felt is a quick, low-cost-of-effort repair that restores quiet, consistent contact with the arrow. Clean the cradle thoroughly, choose a pad that matches your rest, and check clearance before you shoot. A few minutes of careful work now can prevent tuning headaches later.
Related reading
- Trophy Ridge Sync Arrow Rest: 5 Best Picks Compared (2026)
- Traditional Bow Arrow Rest: 7 Best Picks Compared for 2026
- Top 7 Archery Bow Arrow Rest Options Compared for Recurve and Compound Bows
- Ripcord Ratchet Arrow Rest: How It Works, Setup Steps and Tips
Ready to choose one?
