We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Apex Gear Covert 4 Pin Bow Sight: Setup, Sight-In and Tips

Learn how to set up and sight in an Apex Gear Covert 4 pin bow sight, with pin spacing, tuning steps and common beginner mistakes to avoid.

Updated November 2026

An apex gear covert 4 pin bow sight is a multi-pin sight that mounts to your bow’s riser and gives you four fixed or adjustable aiming points, each set for a different yardage. To get it working, you mount it level, set the top pin for your closest distance, and sight in each remaining pin at a set distance using the same anchor and release every time.

Why a Four-Pin Sight Can Seem Off at First

Most new owners of a four-pin sight expect each pin to line up with its distance right away. In practice, the pins are only accurate once the bow is tuned, the sight is level, and your anchor is consistent. A sight that was shot in with a different draw length or a loose release will shift the impact point, and the pins will look wrong even though the sight itself is fine.

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

Four pins also mean more chances for error. Each pin needs its own adjustment, and a small change in one can throw off the spacing you already set. Plan on sighting in one pin at a time and rechecking the first pin after you finish the others.

Factors That Affect Pin Accuracy

Several things control whether your pins hold their marks:

  • Bow tuning. Arrows should fly straight. Paper-tune or bare-shaft test your setup before you touch the sight, because a poorly tuned bow will never group well no matter how you set the pins.
  • Anchor point. Use the same anchor and draw length on every shot. Mark a string peep or nock point so you can return to the same spot.
  • Sight level. Use a bubble level on the sight bar or the riser. A tilted sight will move the pins sideways at distance.
  • Arrow and point weight. Changing arrow weight or field point versus broadhead shifts the impact point, so sight in with the setup you plan to hunt or shoot with.

How to Set Up and Sight In Your Four Pins

  1. Mount the sight to the riser at the height your anchor requires, and confirm it is level with the bow in a shooting position.
  2. Set the sight so the bottom pin is roughly centered on the target at your shortest distance, then loosen the pin housing just enough to move it.
  3. Shoot a three-arrow group at 20 yards. Move the pin until the group sits where you want the arrows to land. Tighten the pin securely.
  4. Repeat for each remaining pin at its set distance, such as 30, 40 and 50 yards, working from closest to farthest.
  5. Shoot a group at each distance to confirm the pins are holding. Make small adjustments of about one-quarter inch at a time.

Check the owner’s manual for the exact pin ranges and recommended adjustment direction. Manufacturers vary on how far each pin travels, so follow their instructions for your model.

Practical Tips for New Archers

  • Shoot from a fixed, marked distance rather than estimating, and measure with a rangefinder or tape.
  • Recheck the sight after a few weeks of shooting, since string stretch and bow tuning changes can move your pins.
  • Keep your release and form the same from shot to shot. Consistent form matters more than any single pin setting.
  • If your pins drift, look first at your form and tuning, then at the sight.

For a broader look at pin setup on other sights, see Apex Gear 3 Pin Bow Sight: Setup and Sight-In Guide for Beginners and Single Pin or Multi Pin Bow Sight (2026): Which Is Better for Beginners?. If you are adjusting a pin that has already been set, Adjusting Bow Sight Pins: A Step-by-Step Guide for Beginners covers the process in more detail.

What We’d Use

  • A bubble level that clips to the sight bar, which helps you confirm the sight is level before you start sighting in. View on Amazon
  • A string peep sight, which gives you a fixed reference point for your anchor so your pins stay consistent. View on Amazon

FAQ

How far should I sight in the first pin?

Start with the closest distance you expect to shoot, often 20 yards. Use that pin as your baseline for the others.

Why do my pins drift after a few weeks?

String stretch, changes in draw length, or small tuning shifts can all move the impact point. Recheck your pins regularly.

Should I consult a professional before adjusting my sight?

If your bow is not shooting straight or the sight appears damaged, have a qualified archery shop inspect it before making major changes.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.