How to Install Peep Sight Without Bow Press: A Step-by-Step Guide
Learn how to install a peep sight without a bow press using a bow square, a few careful steps and the right tools. Get a level, square anchor every time.
Updated November 2026
You can install a peep sight without a bow press by tying the peep into your bowstring with a bow square, a bit of patience and a simple check of alignment. The peep sits in the string at your anchor point, and it needs to be square to the string and at the correct height for your draw. Once it is tied and checked, you can tune it to your eye and begin shooting with a consistent sight picture.
What You Need Before You Start
- A peep sight with the correct size and sight-hole diameter for your eye
- A bow square or a rigid square with a straight edge
- Serving thread or bowstring serving material that matches your string
- Scissors or a sharp blade
- A bow stringer, if your bow requires one for safe string removal
- A tape measure or ruler and a marker
Steps to Tie the Peep Sight in the String
- Check your bow and string. Make sure the string is in good condition. A frayed or stretched string should be replaced before you add a peep.
- Find your anchor point. Draw the bow to your normal anchor and have someone mark the string at the corner of your mouth, or use a fixed reference point on your face. Mark the string at the spot where the peep should sit.
- Position the peep. Hold the peep at the mark with the sight hole facing you. Use the bow square to confirm the peep sits perpendicular to the string. The peep should be square to the string, not tilted.
- Tie the peep in. Wrap serving thread tightly around the string on both sides of the peep, keeping each wrap snug and even. Stop when the peep is firmly locked in place and cannot slide.
- Finish the knots. Tie off the serving with a secure knot, then trim the ends close to the string.
- Test the fit. Draw the bow and confirm the peep lines up with your eye through the hole. Adjust the position by re-tying if needed.
Checking Alignment and Height
A peep that is square and at the right height makes your sight picture repeatable. Many archers set the peep so the sight hole is centered on the eye, with the peep sitting slightly above or below the nock depending on the sight and draw style. The table below gives a general reference for common checks.
Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).
| Check | What to Look For |
|---|---|
| Square to string | Peep sits at a right angle to the string on the bow square |
| Centered in eye | Sight ring looks round and even when you draw |
| Height at anchor | Peep sits at a repeatable spot at your anchor |
| Stability | Peep does not twist or slide after several shots |
For more detail on the peep’s placement and fine-tuning, see Bow Peep Sight Tube: How to Install and Align One (Step by Step) and Bow Peep Sight String: How to Install and Set Yours (Step by Step).
Tips and Common Mistakes
- Do not tie the peep too loosely, or it will slip under the pressure of the draw.
- Avoid placing the peep off-center, since a crooked sight picture leads to inconsistent groups.
- Check the peep after the first few shots, because a new string may stretch slightly.
- If the peep twists, see Peep Sight on Bow Keeps Twisting? How to Fix It Step by Step.
- Never draw or release the bow with the string unsafe. If you are unsure about string removal or adjustment, consult a qualified archery shop or pro shop.
Recommended Gear
A bow square makes it far easier to keep the peep perpendicular to the string while you tie it. A good serving thread that matches your bowstring also helps you wrap a tight, even bind.
- A bow square helps you check that the peep sits square to the string before you tie it. View on Amazon
- Serving thread gives you a secure wrap that holds the peep in place. View on Amazon
FAQ
Can I install a peep sight without a bow press?
Yes. You can tie the peep in with serving thread and check its position with a bow square, as long as you take care to keep it square and secure.
How do I know if the peep is at the right height?
Draw the bow to your normal anchor and look through the peep. The sight hole should look round and centered, and the peep should sit in the same place every time you draw.
Should I replace my bowstring when adding a peep?
Not always, but a worn or stretched string should be replaced before you add a peep. If you are unsure of your string’s condition, ask a qualified archery technician to inspect it.
Conclusion
Installing a peep sight without a bow press comes down to a square placement, tight serving and a careful check at full draw. Take your time with the marks and the alignment, because a well-set peep pays off in tighter groups. Recheck it after your first few sessions as the string settles.
Related reading
- Bow Sight Without Peep: Setup Steps for Accurate Shots (2026)
- Bow Sight Mounting Screws: How to Install and Tighten Them Correctly
Ready to choose one?
