We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Triple Stack Bow Sight: How to Set Up and Sight In a Three-Pin Sight

Learn how a triple stack bow sight works, how to set and sight in its three pins, and the common mistakes that throw off your groups.

Updated November 2026

A triple stack bow sight is a compound bow sight with three pins stacked vertically, each set for a different distance. This guide walks you through choosing the right pin spacing, mounting and sighting in the sight, and tuning it so the pins hit where you aim at 20, 30 and 40 yards. Expect a sight that is repeatable and ready for the range within one session.

What a Triple Stack Sight Does

Each pin on a triple stack sight is a fixed aiming point. The top pin is usually set for your longest distance, the middle pin for a mid-range distance and the bottom pin for close shots. Because the pins are stacked, you pick a distance by choosing which pin to place on the target, rather than moving a single pin up and down. That makes the sight quick to use, but it only works well if the pins are set accurately for your bow, arrow and draw length.

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

Setting Up the Sight Before You Shoot

Start with the basics. Mount the sight so the pin housing is level and the sight bracket is secure. Check that the sight is aligned with your arrow path, since a sight mounted off-center will push groups left or right no matter how carefully you aim. Confirm that the bow is tuned first. A bow that is out of tune will make sight adjustments look like they are failing when the real issue is arrow flight.

Sighting In All Three Pins

Sight in one pin at a time, starting with your most-used distance. Work through these steps:

  1. Shoot a group of three to five arrows at your first distance with the pin you are adjusting.
  2. Measure the center of the group relative to the bull. Note whether the group is high, low, left or right.
  3. Move the pin in the direction of the error. Most sights use a windage screw for left and right and an elevation adjustment for up and down.
  4. Shoot another group and repeat until the group centers on the bull.
  5. Once that pin is set, move to the next distance and repeat the process.

Shoot from the same stance and anchor point each time. Small changes in form will shift your groups and make the sight look inaccurate.

Checking Your Pin Spacing

Pin spacing on a triple stack should match your shooting distances. A common approach is to set the bottom pin for 20 yards, the middle pin for 30 yards and the top pin for 40 yards, though many archers use a different set based on their hunting or target needs. Verify the spacing by shooting at each marked distance. If a pin is consistently off at the same distance, the issue is usually the pin setting rather than the spacing itself. Check your sight manual for the adjustment range and the recommended pin setup for your model.

Common Mistakes

  • Sighting in with a bow that is out of tune, which makes the sight appear inaccurate.
  • Changing your anchor point or release between groups.
  • Shooting at unmarked distances and assuming the pin will still hit.
  • Tightening adjustment screws too far and stripping them.
  • Ignoring a sight that loosens during shooting; recheck mounting hardware often.

A sight wrench set helps you make small adjustments without stripping screws. View on Amazon

A bow square lets you check that your sight bracket is square to the arrow path before you begin sighting in. View on Amazon

FAQ

How far apart should the pins be on a triple stack sight?

Pin spacing depends on your target distances and your bow’s arrow speed. Set each pin for a distance you actually shoot, then verify by shooting at those marks.

Why does my triple stack sight keep shooting high or low?

Check that the bow is tuned and your anchor is consistent first. If the group stays off at the same distance, adjust that pin’s elevation until the group centers.

Can I use a triple stack sight for hunting?

Yes, many hunters use them, but practice at the distances you expect to shoot in the field. For more on setup and calibration with rangefinder sights, see Garmin Rangefinder Bow Sight: Setup, Calibration and Use Guide.

Conclusion

A triple stack bow sight is quick and repeatable once each pin is set for a known distance. Tune your bow, sight in one pin at a time and shoot from a consistent anchor. If your groups still drift, check Why Do Archery Attack Bows and Arrows Miss? 6 Causes and Fixes for other causes before blaming the sight.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.