We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Hha Bow Sight Tape: How to Apply and Use It for Accurate Aiming

Learn what hha bow sight tape is, how to apply it to your bow sight and when to use it for accurate, repeatable aiming on target and in the field.

Updated November 2026

An hha bow sight tape is a strip of adhesive scale marked with distances that helps you set and repeat your sight pins. This guide explains what the tape does, how to apply it cleanly to a bow sight and how to use it during tuning and shooting. By the end, you will have a sight setup you can read at a glance.

What hha Bow Sight Tape Does

Most target and hunting sights use a bracket with one or more pins that you set to match distance. The tape sits on or beside the sight housing and gives you a reference scale, so you can record the position of each pin at a given yardage. Owners often report that a tape scale makes it easier to repeat settings after a bow is taken down, moved or adjusted for a new arrow setup.

The tape does not change your accuracy by itself. It is a record of your sight settings. Your form, arrow tune and sight alignment still decide where the arrow lands.

Preparing the Sight for Tape Application

Clean the surface before you apply anything. Oil, grease and dust will keep the adhesive from bonding and cause the strip to lift during shooting. Follow these steps:

  1. Remove the sight from the bow if you can reach the mounting surface more easily that way.
  2. Wipe the area with isopropyl alcohol on a lint-free cloth and let it dry fully.
  3. Check that the sight housing is tight and the pins move smoothly, since loose parts will shift the tape reading.
  4. Decide where the scale will sit so it does not block your sight window or the pin movement.

Applying the Tape Step by Step

Apply the tape in a consistent position on every bow you tune. Work slowly, because repositioning adhesive tape often leaves residue.

  1. Cut a length of tape a little longer than the scale area you need.
  2. Align the zero mark with a fixed reference on the sight, such as the bracket edge or the mounting block.
  3. Press the tape down from the center outward to remove air pockets.
  4. Run your thumb along the full length to set the adhesive.
  5. Draw the bowstring and check that the tape does not touch the string, cable or your hand during a full draw.

Reading and Recording Your Sight Settings

Once the tape is in place, record each pin position at a set distance, such as 20, 30, 40 and 50 yards. Use the same draw length, anchor point and arrow setup each time. Changing any of these will change the pin positions you have recorded.

Distance Pin position on tape Notes
20 yards Record your mark Confirm with a group of arrows
30 yards Record your mark Check after any bow adjustment
40 yards Record your mark Re-verify in changing light
50 yards Record your mark Use a marked range for accuracy

If your pins drift away from the recorded marks, check the sight bracket and mounting screws first. For a broader look at how sights fit into your setup, see Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

Common Mistakes to Avoid

  • Applying tape to a dirty or oily surface, which leads to peeling.
  • Placing the scale where it touches the bowstring or your hand at full draw.
  • Recording marks with different anchor points or arrow lengths and treating them as one set.
  • Assuming a tape reading is correct without shooting a group to confirm it.
  • Re-tightening the sight without checking whether the tape mark has shifted.

Isopropyl alcohol and lint-free cloths make surface prep easier and reduce adhesive failure.

A small set of hex keys matched to your sight bracket helps you keep mounting screws tight so your recorded marks stay accurate. View on Amazon

A fine-tip permanent marker lets you label distances on the tape without covering the scale numbers. View on Amazon

FAQ

Does hha bow sight tape affect arrow accuracy?

No. The tape only records sight positions. Accuracy depends on your form, arrow tuning and sight alignment.

Can I remove and reapply the tape?

You can, but adhesive residue and stretching may change the reference. Recheck your marks with a group of arrows after any reapplication.

Should I consult a professional about my bow setup?

If your sight or bow shows damage, or you are unsure about mounting or tuning, consult a qualified archery pro shop before shooting.

Conclusion

An hha bow sight tape gives you a repeatable reference for your sight settings when applied cleanly and placed clear of the string. Record your marks under consistent conditions and verify them with real groups. With that routine, your sight setup will stay reliable from session to session.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.