We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Adjusting Bow Sight Left and Right: A Step-by-Step Guide for Archers

Learn how to adjust bow sight left and right so your arrows group true. Follow these steps for windage tuning, checks and fixes for compound and recurve bows.

Updated November 2026

Adjusting bow sight left and right, also called windage, lets you move your pin so your arrows land in the same horizontal line as your aim point. You will set the sight once, confirm it at a known distance, and make small corrections until your groups center on the target. The process takes about 20 to 30 minutes if your bow is already tuned.

Before You Start: Check Your Bow Tune

A sight cannot fix a bow that shoots poorly. Before you touch the windage adjustment, confirm that your arrows fly straight. Paper tuning or bare-shaft tuning will show whether the arrow leaves the bow cleanly. If your arrows fishtail or hit consistently to one side regardless of sight position, correct the tune first. Also confirm that the sight is mounted solidly with no loose hardware.

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

Step-by-Step Windage Adjustment

  1. Set up a target at a known distance, commonly 20 yards. Use a bale or target face with a clear aiming mark.
  2. Shoot a group of three to five arrows with your normal form. Use the same anchor, release and aiming point every time.
  3. Measure the group center relative to the bullseye. Note how far left or right it sits.
  4. Loosen the sight’s windage lock or set screw just enough to move the sight housing. Do not remove it.
  5. Move the sight toward the side where your arrows are landing. If your group is to the left, move the pin to the left. Many sights mark direction on the housing.
  6. Retighten the lock, then shoot another group to confirm the change.

How Much to Move

Make small changes. A common starting rule is to move the sight about the same distance you measured the group off center, then reassess. Large jumps often overshoot and waste arrows. Shoot at least one group after each change before adjusting again.

Checking Windage at Different Distances

Windage set at 20 yards is usually close at 30 or 40 yards, but a sight pin can drift if the lock loosens. Confirm your setting at the distances you shoot most often. Use the same method at each distance: shoot a group, measure the center, and make small corrections if needed.

Group Position Likely Adjustment
Group center left of bullseye Move sight left
Group center right of bullseye Move sight right
Group centered but wide Check tune and form before adjusting sight

Common Mistakes

  • Adjusting windage to fix a tuning problem. Correct the tune first.
  • Changing form between groups, which makes your results unreliable.
  • Forgetting to retighten the lock, causing the sight to drift during shooting.
  • Making large moves instead of small, measured changes.
  • Judging the setting from one arrow rather than a group of three to five.

A stable target and a level shooting setup make groups easier to read. A bow vise or stable stand helps you keep the bow still while you adjust the sight, so your changes are not mixed with setup error. View on Amazon

A sight level or bubble level keeps the sight aligned vertically, so windage changes do not get confused with cant. View on Amazon

FAQ

Can I adjust windage without a bow press?

Yes. You can loosen the sight lock and move the housing by hand. A bow press is useful for tuning but is not required for basic windage work.

How do I know if the sight or the arrow is causing the miss?

If groups consistently shift in one direction at a fixed distance, the sight is usually the cause. If the arrows fly erratically or fishtail, check your tune and nocking point first.

Should I check windage every time I shoot?

Check it after any sight adjustment, after changing equipment, and periodically during the season. If the sight has been bumped or your bow has been transported, a quick group confirms the setting.

Conclusion

Adjusting bow sight left and right is a simple process once your bow is tuned. Shoot a consistent group, measure where it lands, and move the sight in small steps until your arrows center. Recheck at your regular distances, and consult a qualified archery shop or coach if groups stay off after your adjustments.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.