We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Bow Sight Without Peep: Setup Steps for Accurate Shots (2026)

Learn how to set up a bow sight without peep for accurate shots. Covers anchor points, pin alignment, and sight checks for compound and recurve bows.

Updated November 2026

A bow sight without a peep sight is a common setup for target archers who want a consistent reference point without a peep sight in the string. This guide explains how to set up a bow sight without peep, find a repeatable anchor, align your pins, and check your work so your groups tighten up. The steps below apply to most compound bows and many recurve setups with a sight mounted on the riser.

Why Skip the Peep Sight?

A peep sight is a small ring inserted in the bowstring that lines up with your sight housing. Some archers leave it off because it adds one more part to tune, can twist with string wear, and is not required for every shooting style. Without a peep, you rely on a fixed anchor point and a consistent draw length. That makes your form more important, so the setup needs to be deliberate.

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

Setting Up a Bow Sight Without Peep, Step by Step

  1. Mount the sight on the riser at a comfortable height so your eye sits roughly in line with the sight housing when you draw.
  2. Set your draw length. Most manufacturers specify this in their setup guide, and the number should match your actual draw, not a guess.
  3. Choose a anchor point you can repeat every shot. Common options are the corner of your mouth or the tip of your nose, with the string touching the same spot on your face each time.
  4. Draw the bow at full draw and check that your eye sees the target cleanly through the sight without leaning your head.
  5. Adjust the sight left or right so the pin stack is centered behind your arrow, then lock the sight in place.

Finding Your Anchor and Sight Alignment

Your anchor point does most of the work in a peepless setup. Draw the bow slowly to your chosen anchor, then close one eye and check the sight picture. If the pins drift when you change your head position, the anchor is not repeatable enough yet. Try a firmer string contact or a different landmark until the picture stays steady across several draws.

Once the anchor is set, adjust vertical height so your top pin sits at the distance you plan to shoot first, often 20 yards for a beginner setup. Adjust horizontal position so the arrow flies straight at that distance. Keep notes on each setting so you can return to the same position after a change.

Checking Your Setup at the Range

Shoot a group of at least six arrows at a single distance. Measure the spread and check where the group sits relative to your aim point. A tight group that sits high or low means the vertical pin needs adjustment. A group that drifts left or right means the horizontal setting needs correction. Make one change at a time and shoot another group before adjusting again.

Symptom Likely cause Adjustment
Group high at all distances Vertical pin set too high Lower the pin slightly
Group left of target Sight set too far left Move sight right
Wide, inconsistent groups Anchor not repeatable Reset anchor point and shoot again

For a deeper look at troubleshooting a shot that misses, see Why Do Archery Attack Bows and Arrows Miss? 6 Causes and Fixes.

Common Mistakes

  • Changing anchor point between shots, which moves your sight picture.
  • Adjusting multiple settings at once and losing track of what worked.
  • Setting the sight at a distance you rarely shoot, then wondering why groups look off.
  • Ignoring draw length. A mismatch can shift your anchor and throw off alignment.
  • Skipping a check after the string or cams are replaced.

A stable bow sight with fine adjustment knobs makes small corrections easier to repeat. View on Amazon

A stiff bow sight level helps confirm the sight is square to the bow, which keeps your pin picture honest from shot to shot. View on Amazon

FAQ

Can I shoot a bow sight without a peep on a compound bow?

Yes. Many compound shooters run a peepless setup, but they rely on a firm, repeatable anchor and a properly set draw length.

How do I know if my anchor point is consistent?

Shoot a group of six arrows, then repeat the same anchor for another six. If the groups stay within a similar area, the anchor is working.

Should I consult a professional for bow setup?

For draw weight, cam timing, or any structural issue, consult a qualified bow technician before making changes.

Conclusion

A bow sight without peep works well when your anchor is repeatable and your sight is aligned at a distance you actually shoot. Set the anchor first, adjust one sight setting at a time, and record each change. With that process, your groups will tighten and your setup will be easier to trust.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.