We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Adjusting a Bow Sight: A Step-by-Step Guide for Beginners

Learn adjusting a bow sight step by step: set the sight pin for your draw, confirm windage and elevation at 20 yards, and tune for accuracy.

Updated November 2026

Adjusting a bow sight means setting each pin so it lands where your arrow hits at a known distance. By the end of this guide, you will have a sight that is level, centered and tuned for the distances you actually shoot. The process takes one trip to the range if your bow is already tuned, and a little longer if it is not.

Before You Start: Check the Basics

A sight cannot compensate for a bow that is out of tune. Before touching the sight, confirm that your arrows are the correct spine for your draw weight and length, that the nock point is set, and that your bow is shooting paper-tear clean. Your draw length should also be consistent, since changes in draw length shift your point of impact.

Shopping for one? See our guide: Bow Sights with Rangefinder: 5 Best Picks Compared (2026).

Step 1: Set Level and Centered Windage

Start with the sight housing itself. Mount the bow on a stable stand or hold it steady, then use a bubble level on the sight bar or the bow riser to confirm the sight is vertical. Next, check that the sight pin sits directly over the arrow when you look down the riser. Tighten the mounting bolts only after you have made these corrections.

Step 2: Sight In at 20 Yards

Most archers begin at 20 yards because it is close enough to group arrows reliably and far enough to show errors clearly. Shoot three to five arrows, then compare the group to your bullseye.

  1. Measure exactly 20 yards and mark your shooting line.
  2. Shoot a group of three arrows, using the same anchor and release every time.
  3. Note whether the group sits high, low, left or right of the center.
  4. Adjust the sight pin for the 20-yard pin first, moving the pin in the direction of the group.
  5. Shoot another group and repeat until the arrows land in the center.

Move the pin up to raise the group and down to lower it. For windage, move the pin left to move the group left and right to move it right. Make small adjustments, usually a quarter turn of the adjustment screw at a time, and shoot a fresh group after each change.

Step 3: Set Your Remaining Pins

Once the 20-yard pin is tuned, move back to 30, 40 and 50 yards, or whatever distances you plan to shoot. Adjust each pin in turn, shooting groups at each distance. Because the arrow drops more at longer ranges, the pins will sit progressively lower on the sight bar. Verify your work by shooting at a mix of distances and checking that the groups hold together.

Quick Reference

Problem Likely Cause Adjustment
Group high Pin too low Raise the pin
Group low Pin too high Lower the pin
Group left Windage off Move pin left
Group right Windage off Move pin right

Common Mistakes

  • Adjusting the sight before confirming the bow is tuned, which chases an error that is not in the sight.
  • Changing anchor point or release between groups, which shifts the impact point.
  • Making large screw turns instead of small, incremental corrections.
  • Tightening the sight mounts before the level and centering are finished.
  • Judging a group from a single arrow rather than three to five shots.

If your groups stay inconsistent after tuning, the problem may be form rather than equipment. For background on what causes misses, see Why Do Archery Attack Bows and Arrows Miss? 6 Causes and Fixes. If you use a rangefinder-equipped sight, Garmin Rangefinder Bow Sight: Setup, Calibration and Use Guide covers calibration steps specific to that type.

  • Bubble level for bow sights: A small magnetic or clamp-on level helps confirm the sight is vertical before you tighten anything. View on Amazon
  • Allen wrench set: Sight adjustments and mounting bolts usually take hex keys, and a full set avoids stripped screws. View on Amazon
  • Target face with distance markings: A target that shows rings clearly makes it easier to judge group placement at each distance. View on Amazon

FAQ

How often should I adjust my bow sight?

Check your sight whenever you change arrows, string, draw length, or peep height, and periodically if your shooting feels off. Small seasonal shifts in string stretch can also move your groups over time.

Should I sight in at 20 yards or 30 yards?

Twenty yards is the most common starting point because it is easy to group and quick to check. Choose a distance that matches how you hunt or compete, then set the rest of your pins from there.

Why do my groups move when I adjust the sight?

Changes in anchor, release or form can shift the impact point even when the sight is unchanged. Keep your shooting routine identical during tuning, and consult a qualified archery pro shop if problems persist.

Conclusion

Adjusting a bow sight comes down to confirming your bow is tuned, leveling and centering the housing, then working through each pin distance with small, measured changes. Shoot groups of three to five arrows and adjust based on where they land, not on a single shot. With a consistent form and a patient approach, your pins will hold their placement at every distance you shoot.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.