We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

QAD Integrate MX Arrow Rest: Setup Steps and Tuning Tips

Learn how to set up and tune a QAD Integrate MX arrow rest for clean arrow flight, with height, timing and tension checks plus common mistakes to avoid.

Updated November 2026

A QAD Integrate MX arrow rest is a drop-away style rest that cradles your arrow until the shot, then gets out of the way. Getting it set up correctly means positioning it at the right height, timing it so it releases cleanly, and tuning it so your arrows fly straight to the target. This guide walks you through each stage so you can get a consistent, repeatable setup.

Before You Start: Gather What You Need

Most of the work requires only a few basic tools. Having everything ready keeps you from stopping halfway through a adjustment session.

  • Hex keys matching the rest’s mounting and adjustment screws (check the manufacturer’s manual for sizes)
  • A bow square and a fletching or arrow-straightening tool
  • A paper tuning kit or a bare-shaft tuning setup
  • A target at 10 to 15 yards and a stable shooting surface
  • Your bow’s draw length and draw weight set to your normal shooting numbers

Step-by-Step Setup of the Integrate MX

Mount the Rest and Set the Height

Attach the rest to the riser using the mounting holes that fit your bow. Set the rest so the arrow sits level with the centerline of your bow when you hold it in a square position. Start with a height that centers the arrow roughly on your nocking point, then fine-tune from there.

Check the Timing and Launcher Position

The arrow should lift off the rest’s cradle at the moment the string leaves it, not before. Adjust the cradle position so the arrow stays supported until the string begins to move forward. If the arrow drops early, the rest is too low or the cradle is set too far back. If the arrow lags behind the string, move the rest forward or raise it slightly.

Set the Tension and Arm Position

Follow the manufacturer’s instructions for tension adjustment. Too much tension can slow the arrow’s exit, while too little can let it wobble. Test in small increments and watch how the arrow leaves the cradle.

Tuning for Clean Arrow Flight

Once the rest is mounted and timed, tune the arrow flight with a paper test. Shoot through a sheet of paper at about three feet. The tear should show the arrow shaft and fletching clearly.

Paper Tear Result Likely Cause Adjustment
Fletching cuts through the tear at the top Rest set too far to the left or right Shift the rest in small steps
Arrow tail tears high or low Rest height or cant off Adjust height and check the bow square
Fletching tear looks wide and uneven Nock point or rest timing off Recheck nock point and cradle timing

Make one change at a time and shoot another paper test after each adjustment. For a broader look at tuning fundamentals, see QAD UltraRest Integrate MX Arrow Rest: Setup, Tuning and Buying Tips.

Common Mistakes to Avoid

  • Skipping the bow square check, which can make a correctly tuned rest look wrong
  • Tightening adjustment screws beyond what the manual specifies
  • Changing several settings at once, which makes it hard to tell what helped
  • Ignoring arrow spine, since a mismatched shaft can make tuning impossible
  • Testing at very close range only, where small errors can be hidden

If you are comparing this rest with others in the same family, QAD Ultrarest Integrate MX2 Arrow Rest Review: Key Features Explained covers how the two designs differ.

  • Bow square: A reliable square helps you confirm the rest and arrow are aligned before any tuning begins. View on Amazon
  • Paper tuning kit: A paper frame makes the tear test easy to repeat at a consistent distance. View on Amazon
  • Hex key set: A complete set covers the small screws found on most drop-away rests. View on Amazon

FAQ

How often should I re-tune my QAD Integrate MX rest?

Recheck the setup any time you change arrows, string, cams or bow weight, and after any impact to the riser. Many archers also do a quick paper test at the start of each season.

Can I install the rest without a bow press?

You can mount the rest on a bow that is strung, but a bow press is safer for changing strings and cams. If you are unsure about any part of the installation, ask a qualified archery technician.

Why does my arrow still fly off target after tuning?

Check arrow spine, nock point height and the bow square before changing the rest again. Persistent problems often come from the arrow or the bow setup rather than the rest itself.

Conclusion

A well-set QAD Integrate MX arrow rest comes down to correct height, timing and tension, confirmed with a paper test. Work through each step slowly and change only one setting at a time. With patient tuning, your arrows will leave the bow cleanly and group more consistently.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.