We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

NAP Apache Arrow Rest: Setup, Tuning and Tips for Beginners

Learn how to set up and tune a NAP Apache arrow rest, from mounting and centering to arrow clearance and common beginner mistakes. Read the full guide.

Updated November 2026

A NAP Apache arrow rest is a drop-away style rest that holds your arrow during the draw and then moves out of the way as the arrow leaves the bow. This guide walks you through mounting it, setting the arrow height and centering, and checking clearance so your arrows fly clean. Most of the work is a handful of measurements you can repeat at the range.

What You Need Before You Start

Gather your tools before you touch the bow. Working from a stable bench with the bow clamped or held in a bow stand will make every adjustment more repeatable.

Shopping for one? See our guide: Arrow Rest for Compound Bow: 6 Best Picks Compared (2026).

  1. Your bow, with the riser clean and the mounting holes free of debris.
  2. The arrow rest with its mounting hardware and the correct Allen keys.
  3. A bow square or a ruler for measuring from the string to the riser.
  4. A cleaned, fletched arrow matching your draw length and spine.
  5. A piece of paper or a strip of tape for checking clearance.

Mounting and Centering the Rest

Start by attaching the rest to the riser in its approximate position, then bring it to center. Set the rest so the arrow sits directly over the center of the riser, then check that the launcher or arrow-holding arm lines up with the string when you look down the bow.

  • Snug the mounting screws finger-tight first, then tighten them fully once the position is right.
  • Measure from the string to the arm at the top and bottom of the rest to confirm both sides are equal.
  • Recheck centering after your first few shots, since vibration can shift the mount slightly.

Setting Arrow Height and Clearance

Arrow height is what keeps the shaft level as it leaves the bow. Set the rest so the arrow sits level with the nock point and sits squarely on the arm without tilting. Then check that the fletching clears the riser and rest body on the way out.

Checking Clearance

Draw the bow slowly with an arrow on the rest and watch the fletching pass the riser. Clearance of roughly a quarter inch from the riser is a common starting target, though your bow manufacturer’s specifications for your model should guide the final number. Adjust the rest up or down, or move it inward or outward, until the arrow clears cleanly.

Tuning for Flight

Once the rest is mounted and clearance is good, shoot a few arrows at a short distance and watch how they group and fly. Paper tuning on a bench is a helpful way to see whether the arrow is leaving straight. Small adjustments in rest position will often correct a tear or fishtail pattern, and you should always recheck clearance after each change.

Common Mistakes

  • Tightening the mounting screws before confirming centering, which makes later adjustment frustrating.
  • Ignoring clearance, which can cause fletching to brush the rest and disturb arrow flight.
  • Setting arrow height by eye instead of measuring from the nock point.
  • Forgetting to recheck the setup after changing arrows, since spine and length affect where the arrow sits.
  • Skipping a periodic check of the mounting hardware, which can loosen with use.

A bow square makes it much easier to measure the string-to-riser distance and confirm centering. Bow square tools are widely available, and View on Amazon is a good starting search.

A paper tuning kit helps you see arrow flight problems on a target without guessing. Look for one designed for compound and recurve bows, such as those sold under the name View on Amazon.

A bow stand or clamp keeps the bow steady during adjustments. View on Amazon is a practical search for a stable work surface.

FAQ

Do I need special tools to install a NAP Apache arrow rest?

Most installations need only the Allen keys included with the rest, plus a measuring tool such as a bow square or ruler. Consult your bow’s manual for the correct mounting hole pattern before drilling or tightening anything.

How often should I check my rest setup?

Check centering, clearance and mounting screws at least once a month if you shoot regularly, and after any change in arrows or string. Frequent use can loosen hardware over time.

Why does my arrow still tear paper after setup?

Tears often come from centering, nock height or arrow spine rather than the rest alone. Make small changes one at a time and retest, and consider a visit to a qualified archery pro shop if the problem persists.

Conclusion

Setting up a NAP Apache arrow rest comes down to careful mounting, measured arrow height and clearance, and a few test shots to confirm flight. Work through each step in order and recheck after every change. With a repeatable routine, your arrows will fly more consistently and your setup will stay dialed in.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.