Screw On Arrow Rest: How to Install One Step by Step
Learn how a screw on arrow rest attaches to your riser, how to set the height and centershot, and the common mistakes that hurt accuracy.
Updated November 2026
A screw on arrow rest mounts to your bow riser with a single threaded bolt or a pair of screws, and it holds the arrow shaft off the riser so it can leave the bow cleanly. This guide walks you through choosing the right position, installing the rest, and making basic height and centershot adjustments. Done carefully, the whole job takes under an hour and needs only a few hand tools.
What You Need Before You Start
Gather the tools and parts before you touch the bow. Missing a single hex key often means stopping halfway through a setup.
- The screw on arrow rest and its included mounting hardware
- Hex (Allen) keys in the sizes listed by the rest maker
- A bow square or a straight edge for checking alignment
- Painter’s tape to mark your reference points
- A bow stand or a stable padded surface to hold the bow
- Your arrows, cut to length and fletched
Step-by-Step Installation of a Screw On Arrow Rest
Most screw on rests use one of two mounting styles: a threaded post that screws into a riser hole, or a bracket that bolts to the riser with two screws. Check which system your rest uses before you begin, since the steps differ slightly.
- Clean the riser. Wipe the mounting area with a dry cloth to remove wax, oil and grit. Debris under the rest can shift your setup over time.
- Locate the mounting holes. Most risers have a row of threaded holes on the shelf side. Choose the pair or single hole the manufacturer recommends for your bow’s draw length and arrow length.
- Attach the rest loosely. Thread the bolt or screws in by hand, leaving them snug but not tight. You need room to slide the rest for fine adjustment.
- Set the rest height. Nock an arrow and draw the bow. The arrow should sit level with the shelf, with the fletching clearing the riser. Adjust the height so the arrow centers on the rest’s contact point.
- Set the centershot. Position the rest so the arrow lines up with the center of the riser when viewed from behind the bow. Shoot a few arrows at a close target and watch for paper tears or fletching contact.
- Tighten and retest. Torque the mounting hardware to the snug point the manufacturer specifies. Shoot a group at 10 yards and recheck the setup.
Checking Arrow Clearance
Draw the bow and watch the fletching as the arrow passes the rest. Any rubbing or contact means the rest is too low, too far forward, or too far from center. Small changes of about 1/16 inch often make the difference between clean flight and fletching strikes.
Factors That Affect Your Setup
Three things control how well a screw on arrow rest performs: arrow spine, draw length and the rest’s position on the riser. Arrow spine is the most overlooked. A shaft that is too stiff or too weak will fly off-center even with a perfect rest setup, so check your arrow spine chart before adjusting the rest.
| Adjustment | What It Changes | Symptom if Wrong |
|---|---|---|
| Height | Vertical arrow position | Arrow drops or climbs at release |
| Centershot | Horizontal arrow position | Arrow walks left or right |
| Tension | Contact force on the shaft | Arrow slides or hops off the rest |
Common Mistakes to Avoid
- Tightening the mounting screws before setting height and centershot, which makes later adjustments difficult.
- Skipping the arrow spine check and blaming the rest for poor groups.
- Leaving the rest slightly loose, which lets it drift during a shooting session.
- Installing the rest with a dirty riser, which can cause the mount to shift.
- Adjusting too many variables at once instead of changing one setting and retesting.
Recommended Gear
A bow square makes centershot checks far more accurate than eyeballing the rest. Look for a Bow Square from a well-known archery brand, sold as a bow square tool. View on Amazon
A small set of hex keys in the sizes your rest needs prevents stripped screws. Search for an archery hex key set that includes metric and imperial sizes. View on Amazon
If you are comparing rest styles before buying, the guide to Types of Arrow Rest: A Guide to Each Style for Archers explains how screw-on designs differ from drop-away and blade options. For a shortlist of screw-in models, see 6 Best Screw-In Arrow Rests for Recurve Bow Picks Compared (2026). Archers working with a specific product can also check Trophy Taker Arrow Rest: Setup, Tuning and Buying Tips for Beginners for a model-specific walkthrough.
FAQ
Can I install a screw on arrow rest without a bow press?
Yes, most screw on rests install with hand tools while the bow is strung. Some manufacturers recommend unstringing the bow for safety, so follow their instructions and consult a qualified bow technician if you are unsure.
How do I know if my arrow spine is wrong?
If your arrows consistently hit to one side even after a careful centershot adjustment, spine is a likely cause. Compare your arrow’s spine rating with your draw weight and length on a manufacturer chart.
How often should I recheck the rest setup?
Recheck after any major change, such as a new string, new arrows or a shift in draw length. Otherwise, a quick check at the start of each season is usually enough.
Conclusion
A screw on arrow rest works best when you set height and centershot in order, then confirm everything with a short group of arrows. Take your time with the arrow spine and mounting hardware, since these two areas cause most setup problems. Once the rest is dialed in, you can focus on your form.
Related reading
Ready to choose one?
