We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Mathews Downforce Arrow Rest: Setup Steps and Tuning Tips

Learn how to install and tune a mathews downforce arrow rest, from positioning and timing to paper tuning, so your arrows fly straight and clean.

Updated November 2026

A mathews downforce arrow rest is a drop-away style rest that holds your arrow until the shot and then gets out of the way. This guide walks you through the basic installation, the position checks that matter most, and a simple paper-tuning routine so your arrows leave the bow cleanly. Work through these steps in order and your setup will be far more consistent.

What You Need Before You Start

Gather everything first so you are not stopping halfway through the setup. A stable bench and good light will make fine adjustments much easier.

  • A hex key set that matches the mounting and adjustment screws on your bow
  • A square or measuring tape for checking the rest’s distance from the riser
  • A sheet of paper tuning paper and a bow stand or sturdy target
  • Your arrows, cut to the correct length and with the nock fitted
  • A bow square or level for checking vertical alignment

Install and Position the Rest

Mount the rest to the riser at the height your arrow shaft will sit on, then position it so the arrow sits level when nocked. Most manufacturers recommend setting the rest so the arrow shaft is centered on the riser’s shooting axis, and checking this with a square or a level before you tighten anything fully. Snug the mounting screws only enough to hold the rest, leaving room for adjustment.

Set the Rest Height and Cant

Adjust the rest height so the arrow sits at center shot as measured from the riser. Check that the rest is not canted off vertical, since a tilted rest pushes the arrow sideways at release. Tighten the screws once the rest is square and level, then recheck both measurements.

Set Drop-Away Timing

The drop-away mechanism needs to release the arrow at the right moment. If the rest drops too early, the arrow can contact the rest arm as it leaves the bow. If it drops too late, the arrow may be pinched or deflected. Follow the timing procedure in the manufacturer’s manual for your draw length and cam system, and check that the rest arm clears the fletching fully during the shot.

Because the mechanism is tied to the bow’s draw cycle, timing can drift over time. Recheck it after any change to your draw weight, cams, or string.

Paper Tune for Arrow Flight

Paper tuning shows you how the arrow leaves the bow, which is more useful than guessing from groups alone. Shoot an arrow through a sheet of paper held about three feet from the bow. A clean tear with the fletching passing through the center means the arrow is flying straight. A tear that is off-center shows the arrow is being pushed sideways or the nock is out of alignment.

  1. Shoot two or three arrows through the paper at close range.
  2. Look at the tear pattern. A consistent tear with a small pointed shape at the bottom is ideal.
  3. Adjust the rest left or right in small increments, then shoot again.
  4. Repeat until the tear is centered and consistent across several shots.

Common Mistakes

  • Tightening the mounting screws before checking alignment, which makes later changes harder.
  • Skipping the level check, which leaves the rest canted and throws off arrow flight.
  • Making large adjustments instead of small, one-direction changes between shots.
  • Ignoring drop-away timing after changing draw weight or cams.
  • Judging tune from a single group rather than from paper tuning results.
  • Bow square for alignment checks. A square makes it easier to confirm the rest is vertical and centered before you shoot. View on Amazon
  • Paper tuning kit. A tuning frame or pre-cut paper keeps your tests consistent from session to session. View on Amazon
  • Hex key set for archery bows. Having the right sizes on hand prevents stripped screws during adjustments. View on Amazon

For more background, see Drop Away Arrow Rest Mathews: Setup, Tuning and Buying Guide and Mathews Bow Arrow Rest: 5 Best Picks Compared for 2026. If you are still deciding between rest types, Types of Arrow Rest: A Guide to Each Style for Archers covers how each design works. Once your setup is dialed in, What Holds Arrows in Archery: Quivers, Arrow Rests and Holders Explained is useful for understanding how the rest fits with the rest of your gear.

FAQ

How do I know if my mathews downforce arrow rest is timed correctly?

Watch the arrow leave the bow in slow motion or on video, and check that the rest arm clears the fletching cleanly. Any contact with the arrow during release means the timing needs adjustment.

How often should I recheck paper tuning?

Recheck after changing arrows, broadheads, draw weight, or the rest position, and periodically if your groups start to drift. A quick paper test takes only a few minutes.

Can I adjust the rest without a bow press?

Basic rest height and left-right adjustments can usually be done by hand with the right hex key. Cam and string work that affects timing may require a qualified bow technician, so consult a professional if you are unsure.

Conclusion

A properly installed mathews downforce arrow rest, with correct height, level mounting, and accurate drop-away timing, gives you a stable platform for every shot. Paper tuning confirms the arrow is leaving the bow cleanly, which is the foundation of good groups. Make small adjustments, test often, and recheck after any change to your bow.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.