We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Archery Arm Guard Size: How to Measure and Choose the Right Fit

Learn how to measure your forearm and choose the right archery arm guard size, with fit checks, common mistakes, and tips for a secure, comfortable fit.

Updated November 2026

Choosing the right archery arm guard size comes down to two measurements: the length of your forearm and the circumference of your forearm at the spot where the guard sits. Get both right and the guard will cover your forearm from wrist to elbow, stay in place during a full draw, and leave your bowstring hand free to release cleanly. This guide walks through how to measure, how to read size charts, and how to check the fit before you shoot.

Measure Your Forearm Length and Circumference

Start with a flexible tape measure and a helper if you can get one. Length is measured from the wrist crease on the inside of your bow arm to the point just below the elbow where you want the guard to end. Keep your arm straight and relaxed, with your palm facing down. Circumference is measured around the widest part of your forearm, usually about two to three inches below the elbow.

Shopping for one? See our guide: 4 Best Archery Leather Arm Guard Options for Target Archers (2026).

Match Your Measurements to a Size Chart

Most manufacturers list guards by length and width, sometimes with labels such as small, medium and large. Compare your numbers to the chart, and when you fall between two sizes, choose the longer one if the guard has adjustable straps, or the one that gives a snug but not tight wrap if it does not. Always confirm the chart’s units before ordering, because some listings use centimeters.

Forearm Measurement What to Look For
Length (wrist to below elbow) Guard should cover the full forearm without reaching the elbow crease
Circumference (widest point) Snug fit with room for one finger underneath the strap
Strap position Straps sit away from the bowstring path and do not pinch

Check the Fit with a Test Draw

Once the guard arrives, put it on and stand in your normal shooting stance. Hold the bow at a relaxed draw and watch where the bowstring travels across the guard. If the string slaps the guard, the guard may be too short, too low or set at the wrong angle. Adjust the straps so the guard stays flat against your forearm, then repeat the draw a few times. The guard should not shift when you lift the bow or when you release.

Signs the Size Is Wrong

  • The guard rides up toward the elbow during the draw.
  • The straps dig into the skin or leave marks after a session.
  • Gaps appear along the forearm, letting the string hit bare skin.

Tips and Common Mistakes

  • Measure with your bow arm in its shooting position, not hanging loosely at your side.
  • Do not measure over a heavy sleeve, since the extra fabric will make the guard feel loose later.
  • Re-check your size if you change how much clothing you wear while shooting, especially in colder months.
  • Expect some break-in with leather guards. A slightly roomier fit may tighten over time.
  • Do not assume a youth or women’s size is the same as an adult size. Compare each chart on its own terms.
  • A flexible tailor’s tape gives clean, repeatable forearm measurements that are easy to record and compare. View on Amazon
  • An adjustable leather arm guard with multiple strap positions makes it easier to fine-tune the fit as your stance changes. View on Amazon

FAQ

Should I measure my forearm with my arm bent or straight?

Measure with your bow arm extended in your normal shooting position, since that is the posture the guard has to cover. A bent arm gives a shorter reading and can lead to a guard that is too short.

What if I fall between two archery arm guard sizes?

If the guard has adjustable straps, the longer size usually gives you more coverage and more room to adjust. If it does not, choose the size that wraps snugly without pinching.

How often should I recheck my arm guard size?

Recheck whenever your forearm measurements change, such as after a significant change in weight or muscle tone, or if you switch to a different bow setup. A yearly check is a reasonable habit for regular shooters.

Conclusion

Measure your forearm length and circumference, compare them to the manufacturer’s chart, and test the fit with a few draws before you commit to a session. A correctly sized guard protects your forearm and keeps your shot consistent. If you have a medical condition affecting your arm or wrist, consult a professional before changing your equipment.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Archery Society.