Leather Archery Back Quiver: A Step-by-Step Guide to Choosing and Setting One Up
Learn how to choose, fit and care for a leather archery back quiver, with clear steps on sizing, mounting and arrow access for target shooting.
Updated November 2026
A leather archery back quiver holds your arrows at shoulder height behind your back, keeping them within reach for quick, repeatable draws. This guide walks you through choosing the right size, adjusting the fit and setting up the quiver so your arrows stay secure and easy to grab. Most new archers need about 20 minutes to get it right the first time.
Choose the Right Size and Style
Start with arrow length and count. Measure your arrows from nock to tip, then pick a quiver with a tube deep enough that the nocks sit at or just above the rim. Shorter tubes make arrows hard to grip, while overly deep tubes let them rattle and snag. Most target archers carry between 6 and 12 arrows, so check the stated capacity against how many you shoot per end.
Shopping for one? See our guide: Bear Archery Traditional Back Quiver Review (2026).
Look at the closure and mounting system as well. Traditional leather designs often use a belt loop, a shoulder strap or both. A Youth Archery Back Quiver: A Step-by-Step Fitting and Setup Guide covers sizing for smaller frames, and the principles carry over to adult models.
Fit the Quiver to Your Body
- Put the quiver on with the arrows loaded and the tube resting against your lower back.
- Adjust the strap so the top of the tube sits about level with your shoulder blades.
- Stand in your normal shooting stance and draw a practice motion. The quiver should not swing into your bow arm or your drawing elbow.
- Reach back without looking. Your hand should find the arrows on the first try, at about the same height every time.
- Tighten the belt or strap until the quiver stays put during a full draw and release, but not so tight that it restricts breathing.
Set Up the Arrows and Stabilize the Quiver
Load arrows with fletching facing the same direction so they slide out smoothly. Many archers mark their arrows or sort them by fletching color to speed up retrieval. A small felt or foam insert at the bottom of the tube keeps tips from wearing the leather and reduces noise when you move.
If the quiver shifts during shooting, check whether it is tilted too far forward or back. Small adjustments to the belt position usually fix the problem. Keeping the arrows snug also prevents clatter that can distract you at the line. For a broader comparison of holders, see What Holds Arrows in Archery: Quivers, Arrow Rests and Holders Explained.
Care for Leather to Extend Its Life
Leather responds to moisture, heat and dirt. Wipe the exterior with a dry cloth after each session, and let it air dry if it gets wet. Apply a leather conditioner sparingly every few months, especially where the belt rubs. Avoid storing the quiver in a hot car or against a damp wall, since both can crack or warp the material. Manufacturers generally recommend keeping leather goods away from direct sunlight.
Recommended gear
A quality leather conditioner helps keep the tube and straps flexible over time, which matters more than any single feature of the quiver itself. View on Amazon
A soft microfiber cloth lets you wipe off dust and moisture without scratching the surface. View on Amazon
Common mistakes
- Choosing a tube that is too short, so arrows are hard to grip during a fast reload.
- Wearing the quiver too low, which pulls the arrows out of reach and disrupts your draw path.
- Storing the quiver with arrows still in it, which can stretch the tube over time.
- Skipping regular cleaning, which lets grit wear through stitching and the leather finish.
- Overtightening the strap, which causes discomfort and makes it harder to shoot smoothly.
FAQ
How many arrows should a leather archery back quiver hold?
Most target archers use one that holds 6 to 12 arrows, matching the number they shoot in a single end. Choose a capacity that fits your current practice routine, with a little room to add arrows later.
Can I wear a back quiver for field archery as well as target shooting?
Yes, though the fit matters more for field work because you will move, crouch and kneel more often. Check that the quiver stays secure on uneven ground before relying on it.
How do I stop a leather quiver from squeaking?
Squeaks usually come from rubbing between the leather and the strap or belt. Apply a small amount of conditioner to the contact points and tighten any loose stitching. If the noise continues, consult a professional leather repair shop.
Conclusion
A well-fitted leather archery back quiver keeps your arrows secure, accessible and out of your way during every shot. Choose a capacity that matches your shooting habits, set the height so your hand reaches the arrows naturally, and care for the leather regularly. With these steps, your quiver will support consistent form for seasons to come.
Related reading
- Push Archery Delta Back Pocket Quiver: Fit, Use and Setup Guide
- Mounted Archery Back Quiver: How to Choose and Fit One for Horseback Shooting
- Fuse Archery 4 Arrow Quiver Review: Key Features Explained
Ready to choose one?
