We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Lace an Arm Guard: A Step-by-Step Guide for Archers

Learn how to lace an arm guard so it stays snug on your forearm, clears the bowstring and doesn't slip during a shot. Step-by-step guide for new archers.

Updated November 2026

Learning how to lace an arm guard takes about five minutes and makes a real difference on the line. A properly laced guard stays centered on your forearm, sits firmly enough that it won’t shift during the draw, and gives the string a smooth path past your wrist. This guide walks through the lacing process and the adjustments that keep it working shot after shot.

What You Need Before You Start

Most guards come with their own lacing cord or a set of straps, so you rarely need extra supplies. Have these ready before you begin:

Shopping for one? See our guide: Maverik Max Arm Guard Review (2026): Features and Performance.

  • The arm guard itself, with its lacing holes clean and undamaged
  • The lacing cord or straps supplied with the guard
  • Your bow arm, in the position you normally hold it at full draw
  • A mirror or a partner to check the placement

Steps to Lace an Arm Guard Correctly

  1. Position the guard on your forearm. Slide it on with the front face toward your bow hand’s back side and the opening facing your body. Center it between your wrist and elbow.
  2. Thread the lace through the first pair of holes. Start at the bottom, near the wrist end. Pull the cord through from the inside so the knot ends up on the outside, where it won’t press against your skin.
  3. Work upward in a criss-cross pattern. Cross the lace over the gap and pass it through the opposite hole, then continue to the top. Keep each pass the same tension.
  4. Snug, don’t strangle. Pull the lace until the guard hugs your forearm, then check that you can slide one finger between the lace and your skin. Your circulation should not feel restricted.
  5. Tie a secure knot at the top. Use a double knot or a square knot, and tuck or trim the loose ends so nothing dangles near the string.
  6. Check the string clearance. Draw the bow to your anchor and confirm the string passes over the guard without catching the lacing.

Adjusting the Fit at Full Draw

Lacing is only half the job. Once the guard is tied, draw the bow slowly and watch for movement. If the guard rotates toward your elbow or shifts toward your wrist, loosen the lace slightly, re-center the guard, and retighten. Many archers find that a guard which feels fine at rest can slide during a full draw, so always test it under load.

If you wear a jacket or long sleeves, lace the guard over the fabric, not under it, and recheck the tension. Thick clothing changes how the guard sits.

Checking Your Form

Bad lacing often shows up as a string slap on the guard or a sudden change in your hold. Watch your follow-through. If the string strikes the guard repeatedly, the guard is either sitting too low, too far toward the inside of your arm, or laced too loosely to hold its position.

Common Mistakes to Avoid

  • Lacing too tight, which can cut off circulation and cause numbness during longer sessions
  • Leaving knots on the inside of the forearm, where they press into skin
  • Skipping the full-draw check and assuming the guard is secure
  • Reusing worn cord that has stretched and no longer holds tension
  • Lacing the guard without first confirming it’s the correct size for your arm
  • Replacement lacing cord: A spare cord lets you re-lace a guard quickly when the original frays or stretches. View on Amazon
  • Full-coverage leather arm guard: Leather guards hold their shape well and suit archers who want a firm, stable fit. View on Amazon

FAQ

How tight should an arm guard be laced?

The guard should feel snug enough that it doesn’t slide during the draw, but loose enough that you can slip a finger under the lacing. If your hand tingles or feels cold, loosen it.

Should the knot be on the inside or outside of my arm?

Place the knot on the outside of your forearm, away from your skin and clear of the bowstring path. This keeps pressure off your arm during the shot.

What if my arm guard keeps slipping while I shoot?

Re-center the guard, tighten the lacing evenly from wrist to elbow, and test at full draw. If it still moves, check whether the guard is the right size. For persistent fit problems, a coach at your range can watch your setup and suggest adjustments.

Conclusion

Lacing an arm guard correctly comes down to centering it, working the criss-cross evenly and checking the tension at full draw. Take the extra minute to test the fit before you shoot, and you’ll avoid string slaps and shifting guards. Revisit the lacing whenever the cord stretches or your clothing changes.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Lauren Holland
Lauren Holland

Lauren Holland writes reviews and buying guides for Archery Society.