How Far Should an Arrow Go Past the Rest? A Setup Guide for Archers
Wondering how far an arrow should go past the rest? Learn the correct arrow-past-rest distance, how to measure it, and how to adjust it safely for your bow.
Updated November 2026
How far should an arrow go past the rest? For most bows, the arrow tip should extend roughly 1/8 inch to 1/4 inch beyond the rest’s arrow support, measured from the rest to the arrow’s nock-end and tip alignment. This setting lets the arrow sit securely on the rest during the draw while leaving enough room for the arrow to clear the rest cleanly on release. Getting this right helps you avoid arrows that fall off the rest, drag, or fly erratically.
Why Arrow Pass-Through Matters
The arrow sits on the rest and leaves the bow through the rest’s opening. If the arrow is too short, the tip may not clear the rest cleanly, and the fletching can snag. If the arrow is too long, the tip extends too far, the arrow loses stability at the rest, and it can wobble. Both problems affect accuracy, so the goal is a consistent, slightly forward setting that you can repeat every shot.
Shopping for one? See our guide: Arrow Rest for Compound Bow: 6 Best Picks Compared (2026).
How to Measure Arrow Past the Rest
Measure with the bow braced and the rest installed, but without drawing the string. Follow these steps:
- Nock an arrow you plan to shoot, and seat it on the rest with the nock engaged on the string.
- Look at the rest’s arrow support and note where the arrow’s shaft crosses the rest’s contact point.
- Measure from the front edge of the rest’s arrow support to the tip of the arrow. Aim for about 1/8 inch to 1/4 inch of arrow tip beyond the support.
- Rotate the arrow once and recheck. The shaft should sit level without tilting or pressing unevenly on the rest.
Adjusting the Arrow Setting Safely
Most rests allow forward or backward adjustment through a slot or set of screws. Loosen the fastener only enough to move the rest, make a small change, and retighten. After each adjustment, nock, draw, and check that the arrow stays seated. Check that the rest is secured after each change. Recheck the arrow setting after you change arrows, because a different shaft length or point weight can shift the ideal distance.
Checking Your Tuning After Adjustment
Shoot a few arrows at a close target and watch for consistent groupings. If arrows fly with a visible tail-left or tail-right pattern, the arrow setting may be interacting with the rest’s alignment. In that case, check the rest’s horizontal position alongside the pass-through distance before making further changes.
Factors That Change the Right Distance
The ideal pass-through depends on your bow type, arrow length, and rest design. Shorter arrows generally need less forward distance, while longer arrows may need slightly more. Drop-away and whisker-style rests each handle contact differently, so the setting may vary slightly between them. Manufacturers specify their own recommended setups, so consult the rest’s instructions for starting points.
Common Mistakes
- Measuring with the arrow pulled into the rest under tension, which shifts the reading.
- Setting the arrow too far forward, causing it to lose support on the rest.
- Skipping a recheck after switching arrow length or point weight.
- Overtightening the rest mount, which can strip threads or crack parts.
- Assuming one setting works for every arrow in your quiver.
Recommended Gear
A few simple tools make setup more precise:
- A digital or dial caliper gives repeatable readings to within a few thousandths of an inch. View on Amazon
- A bow square helps you confirm the arrow sits straight and aligned with the string. View on Amazon
- A set of hex keys covers most rest mounting screws and adjustment fasteners. View on Amazon
FAQ
Can the arrow sit flush with the rest?
A flush setting usually leaves the arrow with no clearance, which can cause contact and snagging on release. Most archers keep a small amount of tip beyond the support for clean launch.
What happens if the arrow goes too far past the rest?
An arrow that extends too far may lose stability on the support and wobble during the draw. It can also shift position as you aim, which hurts consistency.
Should I recheck the setting for every arrow?
Yes, at least when you change arrow length, point weight, or shaft type. Those differences can change the ideal pass-through, so a quick recheck saves guesswork later.
Conclusion
For most setups, aim for about 1/8 inch to 1/4 inch of arrow tip beyond the rest’s support, then verify it with a few test shots. Measure consistently, make small adjustments, and recheck after every change in arrow or rest. A repeatable setting is more valuable than any single perfect measurement. If you are unsure about mounting or tuning your bow, consult a qualified archery pro shop.
Related reading
- Zero Effect Arrow Rest: How It Works and How to Set One Up
- Ripcord Ratchet Arrow Rest: How It Works, Setup Steps and Tips
- Ripcord Arrow Rest Replacement Parts: What to Buy and How to Swap Them
- QAD Arrow Rest Parts: What Each Piece Does and How to Replace It
- Moleskin for Arrow Rest: How to Apply It Right (Step-by-Step)
- Lizard Tongue Arrow Rest: How It Works, Setup and Tuning Tips
Ready to choose one?
