Making an Archery Arm Guard: A Step-by-Step Guide for Beginners
Learn making an archery arm guard step by step: materials, measuring, cutting, shaping and fitting so your forearm stays protected from string slap.
Updated November 2026
Making an archery arm guard is a practical project that protects your forearm from string slap and keeps your sleeve out of the bowstring’s path. In this guide you will measure your forearm, cut and shape a leather guard, attach it securely and check the fit before your first shot. The whole process usually takes an afternoon once you have the materials on hand.
Gather Materials and Measure Your Forearm
Start with a flat strip of leather roughly 1/8 inch thick, which gives enough stiffness to deflect the string without being hard to bend. Measure the distance from the inside of your wrist to just below your elbow on your bow arm, then add about 1 inch for overlap. Measure the width around your forearm at its widest point and add 1 inch so the guard wraps without pinching.
Shopping for one? See our guide: DIY Leather Arm Guard for Archery: 4 Best Picks for Making or Buying (2026).
Tools and supplies checklist
- Leather strip, about 1/8 inch thick, sized to your measurements
- Soft measuring tape and a fine-tip marker
- Utility knife or leather cutting tool with a fresh blade
- Metal straightedge or ruler
- Leather punch or awl
- Strong cord, elastic or Velcro for securing the guard
- Contact cement or rivets, if you plan to attach a backing
Cut and Shape the Guard
Trace your measurements onto the leather, then mark a gentle curve along the inner edge so the guard follows the natural shape of your forearm. Cut slowly with the straightedge as a guide, keeping the blade perpendicular to the surface for clean edges. Round off all corners so nothing snags on clothing or the bowstring.
Add Attachment Points and Secure the Guard
Punch two or three holes along each long edge, spaced evenly and about 1/4 inch from the border. Thread cord or a strap through the holes so the guard wraps snugly, then tie or fasten it firmly. If you prefer a rigid design, attach a thin backing with contact cement and let it cure fully before use.
Steps for a secure fit
- Place the guard on your forearm with the bow arm relaxed.
- Wrap the strap so it is snug but does not restrict blood flow.
- Check that the guard covers the inside of the forearm where the string travels.
- Draw an unloaded bow to confirm the string clears the guard.
Test and Adjust Before Shooting
Once secured, shoot a few arrows at close range to check the guard’s coverage and comfort. Look for any spot where the string touches bare skin, and adjust the placement or add padding if needed. Retighten the straps after your first few shots, since leather settles slightly as it conforms to your arm.
Common Mistakes
- Cutting the guard too short, which leaves the wrist or elbow exposed.
- Making the leather too thin, so it flexes under string impact.
- Fastening the straps too tight, which causes numbness or discomfort.
- Placing holes too close to the edge, where the leather can tear.
- Skipping the unloaded draw check, which can hide a string path problem.
Recommended Gear
- Leather cutting knife: A sharp, controllable blade gives clean edges on thick hide. View on Amazon
- Leather hole punch set: Consistent hole sizes make strap attachment neater and stronger. View on Amazon
- Contact cement for leather: A flexible adhesive helps bond a backing without stiffening the guard too much. View on Amazon
If you would rather start from a proven layout, the DIY Leather Arm Guard: 5 Best Picks for Making or Buying One (2026) article compares ready-made and homemade options. For pattern details, see Archery Arm Guard Pattern Free: How to Make Your Own Step by Step.
FAQ
What leather thickness works best for an arm guard?
Most beginners use leather around 1/8 inch thick, which balances stiffness and flexibility. Thinner leather can flex under string impact, while very thick leather may feel bulky.
How do I know if my arm guard is the right length?
It should cover the inside of your forearm from the wrist to just below the elbow, with no bare skin where the string travels. Check this with an unloaded draw before shooting.
Can I make an arm guard without a backing?
Yes, a single layer of leather works for many archers, especially with a snug strap. A backing adds rigidity, but it is optional for basic protection.
Conclusion
With accurate measurements, careful cutting and a secure strap, you can build an arm guard that protects your forearm well. Test it with an unloaded draw and a few close-range shots before a full session. If the fit feels off, adjust the strap or placement rather than forcing the leather to fit.
Related reading
Ready to choose one?
