STX Cell 4 Arm Guard: How to Fit and Wear It Correctly
Learn how to choose, size, and fit an stx cell 4 arm guard so it protects your forearm, stays put, and doesn't interfere with your bow arm.
Updated November 2026
An stx cell 4 arm guard protects your bow forearm from string slap, and it only does that job well if it fits correctly. This guide walks you through checking the size, positioning the guard, and tightening the straps so it stays in place through a full shooting session. Most fit problems come from skipping one of these steps, so work through them in order.
Measure Your Forearm Before You Buy or Adjust
Start by measuring the length of your bow forearm from the inside of your elbow to the wrist bone. Then measure the circumference around the thickest part of your forearm, usually just below the elbow. Compare those numbers with the size chart the manufacturer publishes, because guards are sized by length and width rather than by a generic small, medium or large label. If your measurements fall between two sizes, choose the larger one and tighten the straps rather than forcing a smaller guard onto your arm.
Shopping for one? See our guide: Maverik Max Arm Guard Review (2026): Features and Performance.
Position the Guard on Your Bow Arm
Hold your bow in your normal shooting stance and slide the guard onto your forearm with the strap side facing away from the string. The guard should cover the inside of the forearm from just below the elbow to near the wrist, with the top edge sitting a finger-width below the crook of the elbow. Check that the guard does not ride up when you extend your arm. If it climbs, lower the top edge slightly or shorten the length by adjusting where the strap sits.
Secure the Straps Without Restricting Circulation
- Fasten the straps starting from the wrist end and working up toward the elbow.
- Pull each strap snug enough that the guard does not shift when you rotate your forearm.
- Slide one finger under each strap. It should fit with light resistance, not tight pressure.
- Draw your bow and hold for several seconds. Check that the guard stays flat and that your fingers and hand do not tingle or go numb.
If you notice numbness, loosen the straps and recheck. Persistent tingling or pain after shooting is worth raising with a doctor or physical therapist.
Check the Guard Through a Full Shot Sequence
Fit is only confirmed once you have shot several arrows. Take a few shots at a moderate draw, then check whether the guard has moved, whether the strap has loosened, and whether the string has touched bare skin. A small amount of rotation is normal, but the guard should return to the same position after each shot without re-adjusting. If the string still contacts your forearm, the guard may be too short or sitting too low, and you should reposition it before continuing.
Common Mistakes
- Choosing a size based on the label alone instead of your measurements.
- Over-tightening the straps, which can pinch the forearm and cause numbness.
- Leaving the guard too low, which lets the string catch the top edge.
- Failing to recheck the fit after a few shots, when loosening often happens.
- Wearing the guard over a sleeve that bunches and shifts under the strap.
Recommended gear
A thin shooting sleeve worn under the guard keeps the guard from rubbing and helps it sit smoothly against the forearm. View on Amazon
A bow stringer and a tape measure help you set up and check your bow before adjusting the guard position. View on Amazon
FAQ
How tight should an stx cell 4 arm guard be?
The guard should stay in place when you rotate your forearm, and you should be able to slide one finger under each strap. Anything tighter risks pinching or numbness.
Can I wear the guard over a shirt sleeve?
You can, but a sleeve that bunches under the strap will shift the guard during shooting. A thin, smooth sleeve or bare skin usually gives a more stable fit.
What if the guard keeps riding up my arm?
Lower the top edge slightly so it sits a finger-width below the elbow crook, and recheck the strap tension. If it still climbs, your forearm may be shorter than the guard length, so check the size chart again.
Conclusion
A well-fitted stx cell 4 arm guard covers the forearm, stays put through a full draw, and leaves your fingers and hand free of numbness. Measure first, position the guard low enough to clear the string, and recheck after several shots. Revisit the fit whenever you change clothing or shooting setup.
Related reading
- STX Cell IV Arm Guard: How to Choose, Fit and Wear It Correctly
- Women's Archery Arm Guard: How to Choose and Fit One Properly
- Welding Arm Guard Pattern: How to Cut and Sew One (Step by Step)
- Traditional Archery Arm Guard: 3 Best Picks for Target Archers (2026)
Ready to choose one?
