We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Elevate 2.0 Arrow Rest: Setup, Tuning and Tips for Beginners

Learn how to set up, tune and troubleshoot the Elevate 2.0 arrow rest, with clear steps, common mistakes to avoid and tips for new archers.

Updated November 2026

The Elevate 2.0 arrow rest is a drop-away style rest that holds your arrow in place at full draw and clears the shelf as you release. In this guide you will learn how to mount it, set the basic position, and check the setup at the range so your arrows fly cleanly. Always follow the manufacturer’s instructions for your specific model and bow, since mounting details can vary.

What You Need Before You Start

Gather everything before you open the bow case. A tidy workspace prevents lost screws and speeds up tuning.

Shopping for one? See our guide: Arrow Rest for Compound Bow: 6 Best Picks Compared (2026).

  • Allen keys matching the rest’s mounting hardware and your bow’s sight and accessory mounts
  • A soft towel or padded stand to protect the riser and limbs
  • A bow square or straight edge for checking alignment
  • Your arrows, cut to the correct length and fletched normally
  • A target at a known distance, ideally 10 to 20 yards for initial checks

How to Mount the Elevate 2.0 Arrow Rest

Step 1: Locate the Mounting Position

Set the rest on your bow’s riser at the height recommended for your arrow length and fletching clearance. Most archers start with the rest tip slightly above the centerline of the arrow shaft, then fine-tune later. Make sure the rest sits square to the bow window so the arrow will travel parallel to the sight line.

Step 2: Tighten Without Overtorquing

Snug each mounting screw evenly, alternating between them so the rest seats flat. Overtightening can strip threads or crack a plastic base, so stop once the rest no longer shifts under light pressure. Recheck the screws after your first session, since they can settle with use.

Step 3: Confirm Clearance

Nock an arrow and draw the bow slowly to full draw, then let down. Watch that the arrow sits fully on the rest arms and that the fletching does not contact the riser or the rest body. If a fletch touches, adjust the height or the angle slightly and test again.

Tuning the Rest for Clean Arrow Flight

Once the rest is mounted, the next job is checking whether the arrow leaves the bow cleanly. Shoot at a paper or target from a close distance and watch the arrow’s flight.

  1. Shoot a group of at least three arrows from 10 yards and note where they land relative to each other.
  2. If arrows tail left, move the rest slightly in that direction, and repeat.
  3. Make small adjustments of one turn or one notch at a time, and shoot another group after each change.
  4. Check your bow’s nocking point and arrow spine as well, since these affect flight just as much as the rest does.

Recognize that rest tuning is a process, not a single setting. A paper tear or bare shaft test can show you whether the arrow is spinning properly as it leaves the bow.

A few supporting items make setup and maintenance easier, though none is required.

  • Bow square: Helps you check that the rest sits perpendicular to the riser and lines up with the arrow path. View on Amazon
  • Paper tuning kit: A simple way to see how the arrow leaves the bow and whether tuning adjustments are working. View on Amazon
  • Replacement rest screws and small Allen set: Keeps spare hardware on hand so a lost screw does not stop your practice. View on Amazon

Common Mistakes to Avoid

  • Skipping the clearance check at full draw, which can cause fletching to rub and drift arrows.
  • Overtightening mounting screws until threads or plastic parts crack.
  • Changing several settings at once, which makes it impossible to tell what fixed or broke the flight.
  • Ignoring arrow spine and nocking point while blaming the rest for every flight problem.
  • Forgetting to recheck screws after the first few sessions.

If you are new to rests in general, it helps to understand the broader options first. What Holds Arrows in Archery: Quivers, Arrow Rests and Holders Explained covers how different holding systems compare, and Quietest Drop Away Arrow Rest: 7 Best Picks Compared (2026) shows how drop-away designs differ in noise and clearance.

FAQ

Does the Elevate 2.0 need special tools to install?

Most setups require only the Allen keys supplied or matched to your bow’s mounts. Check the included instructions to confirm the exact sizes for your model.

How often should I check the rest’s mounting screws?

Recheck them after your first few sessions and then periodically, since vibration can loosen hardware over time. A quick look before a tournament or hunting trip is a good habit.

Why do my arrows still fly poorly after mounting the rest?

The rest is only one part of the system. Check arrow spine, nocking point, and paper tuning results, and consider a qualified archery pro shop if problems continue, since bow and arrow setup can be tricky to diagnose alone.

Conclusion

With the rest mounted square, cleared at full draw, and tuned through short paper and group tests, the Elevate 2.0 should release arrows cleanly. Make one change at a time, keep records of your settings, and revisit the setup whenever your arrows, bow or draw length change. Patience at this stage pays off in tighter groups at the target.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.