We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Install Arrow Rest on Recurve Bow: A Step-by-Step Guide for Beginners

Learn how to install arrow rest on recurve bow in simple steps, from placement and spacing to tightening and a quick tune test, for accurate shots.

Updated November 2026

To install an arrow rest on a recurve bow, you mark the correct height on the riser, position the rest so the arrow sits just above the shelf, and secure it firmly. Once it is in place, you check clearance and tune the setup so the arrow leaves the bow without touching the rest. This guide walks through each step for beginners.

What You Need Before You Start

Gather your tools first so the job goes smoothly. Most rests use a few basic items.

Shopping for one? See our guide: 6 Best Bow and Arrow Rests for Recurve and Traditional Bows (2026).

  • The arrow rest and its mounting hardware
  • A hex key set or the wrench supplied with the rest
  • A ruler or caliper for measuring
  • Painter’s tape to mark positions
  • Your arrows, nocked and fletched as you normally shoot them
  • A clean, dry bow with no grease on the riser

Step-by-Step: Mounting the Rest

  1. Check the riser. Confirm your bow has a rest mounting hole or a flat area where a stick-on or screw-in rest will sit. Clean that spot with rubbing alcohol and let it dry.
  2. Set the arrow height. Nock an arrow and draw it to your anchor. The arrow should sit level with the centershot, which is usually a little below the centerline of the riser. Mark that height with painter’s tape.
  3. Position the rest. Place the rest so its arm sits just under the arrow shaft. Leave the arrow sitting on the arm with no gap and no pressure pushing it up.
  4. Secure the rest. Tighten the screws evenly, or press the adhesive pad firmly for a stick-on model. Keep the rest square to the bow so the arrow does not slide sideways.
  5. Verify clearance. Shoot a few arrows at close range and watch the flight. The fletching should clear the rest with no contact.

Tuning the Rest for Clean Arrow Flight

Tuning turns a rest that is simply attached into one that works. Start small and adjust in tiny increments, usually a few millimeters at a time. For another angle, check out Archery Bow Arrows Set Guide: How to Choose the Right Setup.

  1. Shoot at short distance. Shoot from about 10 yards and look at where the arrow hits relative to the target.
  2. Read the tear. Paper tuning is a common method. Shoot an arrow through a sheet of paper at close range and check the tear. A clean hole means the arrow is flying straight.
  3. Adjust the height or angle. If the arrow tears high or low, shift the rest up or down slightly. Retest after each change.
  4. Lock everything down. Once the tear looks clean, tighten all fasteners and recheck clearance.

Common Mistakes to Avoid

  • Mounting the rest too high, which forces the arrow to climb over the shelf.
  • Skipping the alcohol cleaning, which lets stick-on pads slip off.
  • Overtightening screws and stripping threads in the riser.
  • Making large adjustments at once, which makes it hard to tell what changed.
  • Shooting before confirming that fletching clears the rest.

A few items make installation and tuning easier. Choose tools that match your rest and bow.

  • Digital calipers help you measure arrow height and clearance accurately. View on Amazon
  • Painter’s tape marks positions without leaving residue on the riser. View on Amazon
  • A hex key set covers the sizes most rests and sights use. View on Amazon

FAQ

Can I install an arrow rest without tools?

Stick-on rests need no tools, just a clean surface and firm pressure. Screw-in rests require a hex key or the wrench included with the rest.

How do I know if my rest is too high?

If the arrow tears upward during paper tuning or seems to rise off the shelf, the rest is likely too high. Lower it slightly and retest.

Should I see a professional for setup?

If you are unsure about the riser material or bow limb condition, consult a qualified archery pro or bow shop before drilling or adhering anything to your bow.

Conclusion

Installing an arrow rest on a recurve bow comes down to clean mounting, correct height and careful tuning. Take your time with each adjustment and retest after every change. With a solid setup, your arrows will leave the bow cleanly and your groups will tighten up.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.