We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Install an Arrow Rest: A Step-by-Step Guide for Beginners

Learn how to install an arrow rest on your bow in clear steps, from mounting and centering to setting the right height and checking clearance before you shoot.

Updated November 2026

Learning how to install an arrow rest takes about 30 to 45 minutes and only a few basic tools. By the end, you will have the rest mounted, centered over your riser, set to the correct height, and checked for clearance so your arrow leaves the bow without touching the rest or the fletching. The steps below apply to most drop-away, containment, and flipper-style rests on compound and recurve bows, though your manufacturer’s instructions always take priority.

Gather Your Tools and Check the Bow

Before you start, collect what you need so you are not stopping halfway through. Most installs require only a few items.

Shopping for one? See our guide: Arrow Rest for Compound Bow: 6 Best Picks Compared (2026).

  • Allen (hex) keys that match the rest’s mounting screws
  • A bow square or a ruler for measuring centershot
  • A clean, dry bow with the string in good condition
  • Painter’s tape or a marker for temporary marks
  • A bow stand or padded surface to work on

Unstring the bow only if your rest type requires it. Inspect the riser for old adhesive, dirt, or leftover screws from a previous rest, and clean the mounting area with rubbing alcohol so the new rest seats flat.

Mount the Rest and Find Centershot

Attach the rest’s base plate or mounting bracket to the riser using the provided screws. Snug them enough to hold the rest in place but leave them slightly loose so you can adjust sideways. Most manufacturers recommend starting with the rest near the center of the riser, which is a common starting point for centershot. How to Structure a Running Week: Easy Runs, Workouts and Rest goes further into this.

  1. Place a bow square against the riser, or measure from the grip’s center line to the bow’s center line at the arrow shelf.
  2. Slide the rest left or right until the arrow sits roughly centered on the bow, with the tip near the middle of the riser’s opening.
  3. Tighten the screws fully once the position looks correct.

Centershot is a starting point, not a final answer. Fine adjustments come later during tuning, which is covered in the related guides linked at the end.

Set the Height and Clearance

Height determines how the arrow sits relative to the cable and string path. Lower the rest so the arrow sits at the correct level, then check that the arrow shaft clears the rest arms when drawn and released. Many archers set the arrow so its center line lines up with the nock point on the string, but the exact height depends on your bow and rest design.

For a quick clearance check, nock an arrow, draw the bow slowly, and watch the shaft. It should rest cleanly on the rest surface without binding. Repeat at full draw and during the release motion. If the shaft contacts any part of the rest, adjust the height or position and test again.

Test and Confirm the Setup

Once the rest is placed, shoot a few arrows at close range, about 5 to 10 yards, and watch the flight. Look for any contact marks on the shaft, fletching damage, or the arrow twisting in the air. Tighten all screws after the first few shots, since vibration can loosen them. Recheck height and centershot whenever you change arrows, string, or draw length.

Common Mistakes

  • Tightening screws fully before checking position, which makes later adjustment difficult.
  • Skipping the clearance check and assuming the rest is fine after mounting.
  • Installing a rest on a riser with leftover adhesive or debris, which causes it to sit unevenly.
  • Overlooking the manufacturer’s torque or height recommendations.
  • Forgetting to recheck the setup after changing arrow spine or draw weight.
  • Bow square: A bow square gives you a fast, repeatable way to measure centershot, which makes the initial placement more accurate. View on Amazon
  • Hex key set: A set with multiple sizes ensures you have the correct fit for rest mounting screws without stripping them. View on Amazon
  • Arrow rest cleaning kit: Clean mounting surfaces and adhesive residue make it easier to seat the rest flat on the riser. View on Amazon

FAQ

Do I need to unstring my bow to install an arrow rest?

Often you do not, especially for stick-on or screw-mounted rests. Check your rest’s instructions, because some mounting positions are easier with the string removed.

How do I know if my arrow rest is installed correctly?

The rest is correct when the arrow sits centered, clears the rest without contact during draw and release, and produces clean flight at close range. Recheck after the first few shots.

How often should I check my arrow rest after installation?

Check the screws and position after your first few shooting sessions, then periodically or whenever you change equipment. Vibration can loosen mounts over time.

Conclusion

Installing an arrow rest is a manageable project when you follow a clear sequence: mount, center, set height, and test. Take your time with the clearance check, since that step prevents most problems. If the rest still does not perform well after installation, consider consulting a qualified archery pro shop for tuning help.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.