We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

QAD Arrow Rest Parts: What Each Piece Does and How to Replace It

Learn which QAD arrow rest parts wear out, how to identify each piece, and how to replace them so your arrows fly straight again.

Updated November 2026

QAD arrow rest parts are the small components that hold your arrow in position from draw to release. Knowing what each piece does lets you spot wear early, order the correct replacement, and swap it without disturbing your tuning. This guide walks through the main parts, when to replace them, and how to do the job cleanly.

Identify the Main QAD Arrow Rest Parts

Most QAD rests share a common layout, though exact part names vary by model. Start by identifying the components on your rest before ordering anything. The most commonly replaced parts are the arrow support (the felt or rubber contact surface), the springs and tension components, the cable or cam linkage on drop-away designs, and the mounting hardware.

Shopping for one? See our guide: 5 Best Drop Away Arrow Rest QAD Models for Target and Hunting (2026).

If you are unsure which model you own, check the rest body for model markings and compare them against the manufacturer’s exploded diagram. The guide Ripcord Arrow Rest Parts: What Each Piece Does and When to Replace It covers part roles in a similar way and is useful for comparing layouts.

Know What Each Part Does

Each component affects arrow flight in a specific way:

  • Arrow support or felt: Cradles the shaft during the draw. Worn felt can leave fibers on the arrow or cause inconsistent contact.
  • Springs and tension parts: Control how firmly the arrow sits against the rest and how quickly the rest returns on drop-away models.
  • Cable and linkage: On drop-away rests, these move the arrow support out of the way at release. A stretched or frayed cable changes timing.
  • Mounting hardware: Holds the rest to the riser. Loose screws shift your tuning and can cause erratic groups.

When to Replace Worn QAD Arrow Rest Parts

Replace a part when you see visible damage or when tuning no longer holds. Watch for these signs:

  • Felt that is compressed, torn, or shows a flat spot where the arrow sits
  • Springs that look bent, have lost tension, or no longer return the rest fully
  • Cable strands that are frayed or a cable that has visibly stretched
  • Arrows that fly well at short distance but group inconsistently at longer range, even after you have re-checked your nock height and rest position

Before blaming the rest, confirm your bow is still set up correctly. A worn part can look like a tuning problem, and a tuning problem can look like a worn part.

How to Replace a QAD Arrow Rest Part Step by Step

  1. Take a photo of the rest from several angles before removing anything. This is your reference for reassembly.
  2. Unload the bow, set it in a bow stand, and remove the arrow.
  3. Remove the mounting screws and detach the rest from the riser, or disassemble only the part you are replacing if the design allows.
  4. Remove the worn component, noting the orientation of springs and any washers.
  5. Install the new part and tighten fasteners snugly. Do not overtighten plastic components.
  6. Reattach the rest, confirm the arrow centers on the rest, and check that drop-away movement is smooth and complete.
  7. Re-check your rest height, centershot, and nock height, then shoot a few arrows at a close target to confirm the change.

Common Mistakes

  • Ordering a part by name alone. Match the part to your exact model number.
  • Skipping the reference photo, then reassembling the springs backward.
  • Overtightening screws, which can strip threads or crack plastic.
  • Replacing a part and assuming tuning is unchanged. Always re-check after a swap.
  • Ignoring a frayed cable on a drop-away rest. Replace it before it fails at full draw.
  • Bow stand: Holds the bow steady so you can work on the rest without the riser shifting. View on Amazon
  • Hex key and small screwdriver set: Most rest hardware uses small fasteners, and the right size prevents stripped heads. View on Amazon
  • Arrow square or rest alignment tool: Helps confirm the rest is centered and square after reinstalling it. View on Amazon

FAQ

How often should QAD arrow rest parts be replaced?

There is no fixed interval. Inspect the felt, springs, and cable before each shooting season and replace them when you see wear or when tuning drifts.

Can I replace a QAD rest part without retuning my bow?

Often you can, but you should re-check rest height, centershot, and nock height afterward. Small changes in spring tension or felt thickness can affect flight.

Should a bow shop handle the replacement?

If you are uncomfortable disassembling the rest or your tuning is complex, a qualified archery technician can do the work and verify the setup.

Conclusion

QAD arrow rest parts are simple components, but each one affects how your arrow leaves the bow. Identify the parts on your model, replace them when wear appears, and always re-check your tuning afterward. A methodical approach keeps your groups tight and your equipment reliable.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.