We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Felt for Arrow Rest: How to Choose, Cut and Install It Cleanly

Learn how to choose, cut and install felt for an arrow rest so your arrows fly quietly and clean. Simple steps, common mistakes and tips for beginners.

Updated November 2026

Felt for an arrow rest is a thin strip of material that sits on the rest’s arm or cradle and gives the arrow shaft a soft, low-friction surface. Done right, it keeps the shaft from scraping the rest, cuts down on noise at release and helps the arrow leave the bow with less wobble. This guide walks you through choosing the right felt, cutting and attaching it, and checking the result.

Choosing the Right Felt for Your Rest

Most archers use adhesive-backed felt sold for arrow rests, though plain craft felt with a little glue works too. Look for a dense, smooth felt that will not shred when the shaft slides across it. Thickness matters: thin felt (around 1 mm) lets the shaft sit closer to the riser, while thicker felt adds height and can change your nock height. If your rest has a pre-cut felt cradle, match the new piece to its width and length rather than guessing.

Shopping for one? See our guide: Arrow Rest for Compound Bow: 6 Best Picks Compared (2026).

Preparing and Cutting the Felt

Clean the rest surface first. Remove old adhesive residue with a dry cloth or a small amount of rubbing alcohol, and let it dry completely before you apply anything new. Then measure the area you need to cover. Most drop-away and plate-style rests need a strip roughly as long as the arm or plate, but cut it a little oversized so you can trim it down after fitting.

  1. Measure the contact surface of the rest in millimeters.
  2. Cut the felt about 2 mm wider and 3 to 5 mm longer than the surface.
  3. Use a sharp hobby knife and a straight edge for clean lines.
  4. Test-fit the strip before removing the backing.

Attaching Felt to the Arrow Rest

Once the strip fits, peel the backing and press it firmly onto the rest. Start at one end and work toward the other so you do not trap air bubbles. Hold pressure for about 30 seconds, then let the adhesive cure for the time the manufacturer specifies, which is often several hours. Avoid touching the adhesive surface with your fingers, since oils reduce grip.

Trimming and Final Check

After the adhesive sets, trim the excess felt flush with the edges of the rest. Run a shaft through the rest by hand and watch for snags or lifted corners. The shaft should slide smoothly with no catching and no visible gap between the felt and the rest body.

Setup Checklist

  • Replacement felt matched to your rest’s surface size
  • Sharp hobby knife and straight edge
  • Rubbing alcohol and a lint-free cloth
  • Ruler or caliper for measuring
  • Test arrow for a final check

Common Mistakes to Avoid

  • Skipping the cleaning step, which leaves the new felt poorly bonded.
  • Cutting felt too short, leaving the shaft exposed to the rest body.
  • Using felt that is too thick, which can change nock height and tuning.
  • Shooting before the adhesive has fully cured.
  • Ignoring a shaft that catches, since rough felt can dull or mark arrows.

If you are unsure how felt affects your tuning, a qualified archery pro shop can check your setup. For a broader look at the parts involved, see Ripcord Arrow Rest Parts: What Each Piece Does and When to Replace It. Owners who replace worn felt often find it easier to swap the whole felt section than to repair it, and Arrow Rest Felt Replacement: Step-by-Step Guide for Clean Arrow Flight covers that process in detail.

A sharp hobby knife with replaceable blades makes clean, straight cuts on felt, which keeps the edges tidy against the rest. View on Amazon

Adhesive-backed felt sheets sized for archery rests save you the trouble of gluing craft felt by hand. View on Amazon

A digital caliper helps you measure the rest surface accurately before cutting. View on Amazon

FAQ

Can I use regular craft felt on an arrow rest?

Yes, if it is dense and smooth and you attach it with a strong adhesive. Adhesive-backed felt made for archery is usually easier to apply and holds up better to repeated shots.

How often should I replace arrow rest felt?

Replace it when it looks flattened, frayed or stained, or when arrows start catching or making more noise than usual. Check it regularly, especially if you shoot often.

Does felt thickness change arrow flight?

It can. Thicker felt raises the shaft slightly, which may shift nock height and tuning. After any change, check your paper tune or bare-shaft tune before relying on the setup.

Conclusion

Good felt for an arrow rest is dense, smooth and cut to fit the rest surface with a little extra length for trimming. Clean the rest, attach the felt carefully and let the adhesive cure before shooting. Recheck your tuning after any change to keep your arrows flying clean.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our target archery guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Archery Society.